Abstract:Ti44Al6Nb1.0Cr2.0V alloy was directionally solidified (DS) with cold crucible under different input powers (40 kW, 45 kW, 48 kW and 50 kW; corresponding to temperature gradient of 15.2 K/mm, 21.0 K/mm, 22.9 K/mm, 25.5 K/mm) and the same pulling velocity (8.33 mu m/s). The results show that all the DS samples have the beta-solidification characteristics and when the power is 45 kW or 48 kW, they have the well-DS macrostructure. After DS, the lamellar width becomes smaller and more homogeneous from the as-cast 1650 +/- 1200 nm to less than 710 +/- 376 nm. The higher the power is, the smaller the lamellar width it has. The original casting microcracks can be eliminated after DS and the percentage of small angle lamellas is higher for the well-DS samples. For the DS samples, the nanoindentation hardness in lamella region and the lamellar width yield the relationships of H-N = 16.12d(-0.127) and r(2) = 0.992. When the as-cast and heat treatment (HT) conditions are considered, the relationships are changed as H'(N) = 16.09d'(-0.127) and r'(2) = 0.971. The nanoindentation hardness of B-2 phase and block gamma phase keep almost the same respectively under the different conditions. RT tensile property is improved to average UTS 589.4 MPa and average elongation 1.16% after DS (P = 45 kW) comparing with the original as-cast 498.8 MPa and 0.53%. Trans-granular and trans-lamella fracture is the main fracture mode for the DS samples. After annealing (at 1250 degrees C, 1300 degrees C, 1350 degrees C), lamellar width is coarsen to more than 2002 +/- 1286 nm; B-2 phase segregation is reduced obviously, but some new microcracks form; HT samples exhibits a poor RT tensile property, in which the HT2 sample has a relatively higher property and it yields the average UTS 440.6 MPa and average elongation 0.45%. (C) 2015 Elsevier B.V. All rights reserved.

The Role of Gd Addition in the Microstructure and Mechanical Property of Directionally Solidified Ti46A10. 5WO. 5Si Alloys

Microstructures and Mechanical Properties of a Γ-Tial Alloy Modified by Gd Additions

Microstructure Evolution of Directionally Solidified Ti–46Al–0.5W–0.5Si Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Influence of Gd Content on Microstructure and Mechanical Properties of Cast Al–12Si–4Cu–2Ni–0.8Mg Alloys

Effects of Gd Addition on the Microstructure, Mechanical Properties and Shape Memory Effect of Polycrystalline Cu-Al-Ni Shape Memory Alloy

The Role of Gd on the Microstructural Evolution and Mechanical Properties of Mg-3Nd-0.2Zn-0.5Zr Alloy

Comparison of Microstructures and Mechanical Properties of As-Cast and Directionally Solidified Ti-47al-1w-0.5si Alloy

Achieving fine-grained Ti-V-Al light weight shape memory alloys with higher transformation temperature, superior performances by doping Gd

Effect of Growth Rate and Diameter on Microstructure and Hardness of Directionally Solidified Ti–46Al–8Nb Alloy

Effect of rare-earth element Gd addition on microstructure of TNM-based TiAl alloys

Microstructure and Mechanical Properties of A Rapid Directionally Solidified Ti47al Alloy

Influence of gadolinium on solidification behavior of Ni–Mo-Cr-Gd alloy

Influence of Mn Addition on the Microstructure and Mechanical Properties of a Directionally Solidified Γ-Tial Alloy

Microstructure and Mechanical Properties of Mg–9Li–3Al–xGd Alloys

Microstructure Evolution and Mechanical Properties of Directionally-Solidified TiAlNb Alloy in Different Temperature Gradients

Microstructure Control and Mechanical Properties of Ti44al6nb1.0cr2.0v Alloy by Cold Crucible Directional Solidification

Effect of Growth Rate on Microstructures and Microhardness in Directionally Solidified Ti-47Al-1.0W-0.5Si Alloy

Three-Dimensional Network Structure and Mechanical Properties of Al-Cu-Ni-Fe Cast Alloys with Gd Micro-addition

Lamellar Orientation and Growth Direction of Α Phase in Directionally Solidified Ti-46Al-0.5W-0.5Si Alloy

Characterization of Gd-rich Precipitates in a Fully Lamellar TiAl Alloy