Abstract:The zero-sequence loop inherently exists in the structure of the three-phase open-end winding permanent-magnet synchronous machine (OW-PMSM) system with common dc bus, which provides the circulating path for zero-sequence current (ZSC) and consequently causes the torque ripple and extra system loss. Besides, the common-mode voltage (CMV), which can cause many negative effects, such as the bearing current and the failure of motor bearing, is another concern in the driving system. However, the simultaneous suppression of ZSC and the CMV control of the devices is investigated mainly in the application of the induction machine system and the multiphase OW-PMSM system, whereas it is ignored in the application of the three-phase OW-PMSM system, in which the suppression of ZSC is more complex considering the effect of flux linkage harmonic components. On this basis, this article proposes a strategy that can not only suppress the ZSC, but also eliminate the ripple of CMV in the three-phase OW-PMSM system. In the proposed method, the suppression of ZSC is achieved by synchronously adjusting the duration time of each phase within every control cycle based on the reference voltage of zero-sequence control loop, which can simplify the conventional rearrangement-based scheme. Furthermore, the duration time of each phase is distributed into each switch device of the two inverters, with the principle of eliminating the ripple of CMV. Consequently, both the suppression of ZSC and the CMV control can be achieved easily. Furthermore, the influence of dead time on the CMV control is analyzed, indicating that the CMV control is irrelevant with the dead time. Moreover, the effective modulation range of the proposed technique is analyzed. Finally, the experimental validation is conducted on a three-phase OW-PMSM system with common dc bus.

Improved Direct Torque Control for Open-Winding PMSM System Considering Zero-Sequence Current Suppression with Low Switching Frequency

Direct Torque Control with Zero-Voltage Vector for a Permanent Magnet Synchronous Motor

Negative Sequence Current Suppression of Dual Three-Phase Permanent Magnet Synchronous Machines Considering Inductance Asymmetry

Torque Ripple Suppression Control for Dual Three-Phase Permanent-Magnet Synchronous Motor

Torque Ripple Suppression Method with Reduced Switching Frequency for Open-Winding PMSM Drives with Common DC Bus.

An Effective Direct Torque Control Based on Space Vector Modulation for DTP-PMSM

Zero-Sequence Current Suppression Strategy with Reduced Switching Frequency for Open-End Winding PMSM Drives with Common DC BUS

Zero-Sequence Current Suppression Strategy with Common-Mode Voltage Control for Open-End Winding PMSM Drives with Common DC Bus

Direct Torque Control for Three-Phase Open-End Winding PMSM With Common DC Bus Based on Duty Ratio Modulation

Control Strategy for Open Winding PMSM System Supplied by the Z-source and Voltage Source Integrated Converters

A Sensorless Drive Strategy for Open-End Winding PMSM with Common DC Voltage Based on Lower Switching Frequency

Zero Sequence Current Suppression Strategy for Open Winding PMSG Fed by Semi-controlled Converter

Zero-Sequence Current Suppression Strategy of Open-Winding PMSG System With Common DC Bus Based on Zero Vector Redistribution

Zero-Sequence Current Suppression Method for Fault-Tolerant OW-PMSM Drive with Asymmetric Zero-Sequence Voltage Injection

Adaptive Torque Ripple Suppression Methods of Three-Phase PMSM During Single-Phase Open-Circuit Fault-Tolerant Operation

A V/Hz Based Maximum Torque Per Volt Control in Flux-Weakening Region for Interior Permanent Magnet Synchronous Motors

A modified flux weakening direct torque control for open winding PMSM system fed by hybrid inverter

A Novel Switching-Table-Based Direct Torque Control with Improved Current and Torque Steady-State Performance for Dual Three-Phase PMSM

Torque Ripple Suppression Strategy for Open-Winding PMSM with Zero-Sequence Loop Model-Free Control

Bilateral Four-Segment-Mode Model Predictive Control for Open-Winding PMSM Drives

Improved Model Predictive Current Control for PMSM Drives Based on Dynamic Reference Current