Abstract:Most previous studies on nonlinear Lamb waves are conducted using mode pairs that satisfying strict phase velocity matching and non-zero power flux criteria. However, there are some limitations in existence. First, strict phase velocity matching is not existed in the whole frequency bandwidth; Second, excited center frequency is not always exactly equal to the true phase-velocity-matching frequency; Third, mode pairs are isolated and quite limited in number; Fourth, exciting a single desired primary mode is extremely difficult in practice and the received signal is quite difficult to process and interpret. And few attention has been paid to solving these shortcomings. In this paper, nonlinear S0 mode Lamb waves at low-frequency range satisfying approximate phase velocity matching is proposed for the purpose of overcoming these limitations. In analytical studies, the secondary amplitudes with the propagation distance considering the fundamental frequency, the maximum cumulative propagation distance (MCPD) with the fundamental frequency and the maximum linear cumulative propagation distance (MLCPD) using linear regression analysis are investigated. Based on analytical results, approximate phase velocity matching is quantitatively characterized as the relative phase velocity deviation less than a threshold value of 1%. Numerical studies are also conducted using tone burst as the excitation signal. The influences of center frequency and frequency bandwidth on the secondary amplitudes and MCPD are investigated. S1–S2 mode with the fundamental frequency at 1.8 MHz, the primary S0 mode at the center frequencies of 100 and 200 kHz are used respectively to calculate the ratios of nonlinear parameter of Al 6061-T6 to Al 7075-T651. The close agreement of the computed ratios to the actual value verifies the effectiveness of nonlinear S0 mode Lamb waves satisfying approximate phase velocity matching for characterizing the material nonlinearity. Moreover, the ratios derived from the primary and secondary horizontal displacements generated from nonlinear S0 mode Lamb waves are closest to the real value, which indicates that using horizontal displacements is more suitable for detecting evenly distributed microstructural changes in large thin plate-like structure. Successful application to evaluating material at different levels of evenly distributed fatigue damage is also numerically conducted.

Evaluation of the Localized Plasticity Using the Mixing of Counter-Propagating Lamb Waves

Acoustic Softening and Residual Hardening in Aluminum: Modeling and Experiments

Evolving Fatigue Damage Detection Based on Multi-Component Nonlinear Modulation Mechanism of Tuned Laser-Generated Rayleigh Waves

Evaluation of plastic damage for metallic materials under tensile load using nonlinear longitudinal waves

Nonlinear acoustic characterization of heterogeneous plasticity in bent aluminium samples

Application of Nonlinear Lamb Wave Mixing Method for Residual Stress Measurement in Metal Plate

Nonlinear Responds of Lamb Waves in Plate Structure with Micro-Crack Using Frequency-Mixing Technique

Analytical and numerical studies of approximate phase velocity matching based nonlinear S0 mode Lamb waves for the detection of evenly distributed microstructural changes

Experimental and Numerical Investigation of the Micro-Crack Damage in Elastic Solids by Two-Way Collinear Mixing Method

Experimental Investigation of Second-Harmonic Lamb Wave Generation in Additively Manufactured Aluminum

Micro-Crack Detection Of Nonlinear Lamb Wave Propagation In Three-Dimensional Plates With Mixed-Frequency Excitation

Acoustic anisotropy and localization of plastic deformation in aluminum alloys

Assessment of Material Dislocation Damage by Nonlinear Ultrasound

An iterative method to evaluate one-dimensional pulsed nonlinear elastic wavefields and mixing of elastic waves in solids

Numerical simulation of Lamb wave sensing of low-velocity impact damage in composite laminate

Nonlinear Guided Wave Tomography for Detection and Evaluation of Early-Life Material Degradation in Plates

Nonlinear Ultrasonic Techniques for Testing Micro-Defects in Metal Matrix Composite Structure

Phased array-based nonlinear wave mixing technique: Application to lack-of-fusion porosity characterization in additively manufactured metals

Health Monitoring of Stiffened Metallic Plates Using Nonlinear Wave Interaction and Embedded PZT Transducers

Numerical modeling with experimental verification investigating the effect of various nonlinearities on the sideband peak count-index technique

Nonlinear response to contact impact on the surface of an aluminum alloy AlMg6 exhibiting the Portevin-Le Chatelier effect