Abstract:Recently, various miniaturized electronic systems and the rapid increase in power density of microelectronic devices have created additional requirements for micro-scale heat dissipation technology. To dissipate heat in a micro-scale region efficiently, several creative cooling methods for high heat flux dissipation have been designed on the order of 1000 W/cm(2). Due to its high surface-to-volume ratio, the microchannel heat sink has become the most popular one among emerging technologies and an effective tool for high heat flux thermal management. Nevertheless, in common electronic microchannel cooling systems, the traditional parallel microchannel causes a dramatic pressure loss along channel length. In this regard, the manifold microchannel heat sink cooling technology becomes promising with its high heat dissipation potential and moderate pressure drop penalty. The shortened effective flow length compared with the traditional microchannel provides a smaller pressure drop and delays the onset of the critical-heat-flux point. However, while a number of numerical and experimental studies have been conducted for the single-phase flow in the manifold microchannel, two-phase flow boiling in this kind of channel is not widely employed because of its issues with flow pattern prediction. This work develops a new solver based on open source software OpenFOAM to perform the transient process of subcooled flow boiling in the manifold microchannel heat sink. Additionally, heat transfer in the silicon substrate is considered to improve the accuracy of simulation. Similar to single-phase flow simulation for the manifold microchannel, a unit cell model extracted from the whole cooling plate is employed for the two-phase boiling flow to avoid huge computational costs. Through several reasonable assumptions, the symmetry boundary condition is applied on four lateral surfaces in the unit cell, while uniform heat flux is adopted on the bottom wall. A uniform inlet velocity boundary estimated from the total volume flow rate condition is coupled with a fixed temperature value of 7 degrees C lower than saturation temperature. After the mesh independence test, the self-programming solver and numerical methods are validated by comparing numerical results with experimental data. It is determined that the boiling curve obtained by the empirical rate phase-change model with parameters r(1)=r(v)=100 agrees well with experimental results. Furthermore, heat transfer and pressure drop performance differences are caused by microchannel width w(c) and fin width w(f). In comparison to sample A (w(c)=w(f)=15 mu m), decreasing wc and wf simultaneously leads to lower average wall temperature of the heated surface; the channel pressure drop between inlet and outlet surfaces rises dramatically when the widths decrease. When the total number of microchannels in the manifold microchannel cooling plate remains unchanged, increasing wc results in a decreased wf. Based on experimental results, heat sink sample C shows that the pressure loss can be considerably reduced under the premise of sacrificing a small degree of heat transfer performance, which can be attributed to the increased microchannel hydraulic diameter. The manifold microchannel heat sink with w(c)>w(f) is recommended for practical application due to lower pressure loss and average temperature variation.

Optimization of Manifold Mmicrochannel Heat Sink Based on Equivalent Resistance Model

Optimization of Manifold Microchannel Heat Sink Based on Design of Experiment Method

Optimization of Manifold Microchannel Heat Sink inside Interposer

Flow Manifold Optimization for a Uniform Velocity Distribution in a Laminated Microreactor with Micro‐Pin‐Fin Arrays

Mathematical modeling and multi-objective optimization on the rectangular micro-channel heat sink

Self-driven Manifold Microchannel Heat Sink for Cooling Electronics

Numerical and Experimental Study on Manifold-Distributed Jet Microchannel with Micro-Pin-fins

Investigation of flow and heat transfer performance of the manifold microchannel with different manifold arrangements

Effects of Manifold Designs on Flow and Thermal Performances of Microchannel Heat Sink

Experimental Study on the Flow and Heat Transfer Characteristics of Pin-Fin Manifold Microchannel Heat Sink

Study on the flow and heat transfer characteristics of pin-fin manifold microchannel heat sink

Micro Pin Fins with Topologically Optimized Configurations Enhance Flow Boiling Heat Transfer in Manifold Microchannel Heat Sinks

Efficient Thermal Management of High-Power Electronics Via Jet-Enhanced HU-type Manifold Microchannel

Thermal and hydrodynamic characteristics of single-phase flow in manifold microchannels with countercurrent regions

Study on the performance of a miniscale channel heat sink with Y-shaped unit channels based on entransy analysis

Experimental and Numerical Investigation of Thermal Performance of S-shaped Manifold Microchannel Heat Sinks

Numerical Study on Heat Transfer Efficiency and Inter-Layer Stress of Microchannel Heat Sinks with Different Geometries

Investigation of heat transfer performance of the manifold microchannel heat sink with different interface configurations

Experimental study of embedded manifold staggered pin-fin microchannel heat sink

Multi-objective Parameter Optimization Design of Tapered-Type Manifold/variable Cross-Section Microchannel Heat Sink

Numerical Simulation of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink