Abstract:It is always an interesting research topic for digital receiver (DRX) designers to develop a DRX with (1) ultrawide instantaneous bandwidth (IBW), (2) high sensitivity, (3) fine time-of-arrival-measurement resolution (TMR), and (4) fine frequency-measurement resolution (FMR) for weak signal detection. This is because designers always want their receivers to have the widest possible IBW to detect far away and/or weak signals. As the analog-to-digital converter (ADC) rate increasing, the modern DRX IBW increases continuously. To improve the signal detection based on blocking FFT (BFFT) method, this paper introduces the new concept of accumulatively increasing receiver sensitivity (AIRS) for DRX design. In AIRS, a very large number of frequency-bins can be used for a given IBW in the time-to-frequency transform (TTFT), and the DRX sensitivity is cumulatively increased, when more samples are available from high-speed ADC. Unlike traditional FFT-based TTFT, the AIRS can have both fine TMR and fine FMR simultaneously. It also inherits all the merits of the BFFT, which can be implemented in an embedded system. This study shows that AIRS-based DRX is more efficient than normal FFT-based DRX in terms of using time-domain samples. For example, with a probability of false alarm rate of 10−7, for N=220 frequency-bins with TMR = 50 nSec, FMR = 2.4414 KHz, IBW > 1 GHz and ADC rate at 2.56 GHz, AIRS-based DRX detects narrow-band signals at about −42 dB of input signal-to-noise ratio (Input-SNR), and just uses a little less than N/2 real-samples. However, FFT-based DRX have to use all N samples. Simulation results also show that AIRS-based DRX can detect frequency-modulated continuous wave signals with ±0.1, ±1, ±10 and ±100 MHz bandwidths at about −39.4, −35.1, −30.2, and −25.5 dB of Input-SNR using about 264.6 K, 104.7 K, 40.2 K and 18.3 K real-samples, respectively, in 220 frequency-bins for TTFT.

A TD-ADC for IR-UWB Radars with Equivalent Sampling Technology and 8-Gs/s Effective Sampling Rate

A 10-Bit 250-KS/s 1.24-uW SAR ADC for IoT Sensors with Energy-Efficient Comparator.

A Sub-Sampling 4-Bit 1.056-Gs/s Flash ADC with a Novel Track and Hold Amplifier for an IR-WB Receiver

A Sub-Sampling 4.25 GS/s 3-Bit Flash ADC with Asymmetric Spatial Filter Response

A 10 MS/s 10 bit SAR A/D Converter in RF System

Design of 4-bit parallel sub-sampling A/D converter for IR-UWB receiver.

All-digital Sub-sampling Architecture for an Impulse Radio Ultra Wideband Receiver

Design of A Parallel Low Power Flash A/D Converter for the Sub-Sampling Ir-Uwb Receiver

A High Speed Sampler for Sub-Sampling IR-UWB Receiver

An 8-bit, 8-GS/s Equivalent Sampling Time Domain Analog-to-digital Converter

A low-power 4.224GS/s sampler in 0.13-μm CMOS for IR UWB receiver

An Interleaved Broadband Photonic ADC Immune to Channel Mismatches Capable for High-Speed Radar Imaging

A 6-Bit Low Power Flash ADC with a Novel Bubble Error Correction Used in UWB Communication Systems

A Low-power Sub-sampler in 0.13 μm CMOS for IR UWB Receiver

A Single Channel, 6-Bit 410-Ms/s 3bits/stage Asynchronous Sar Adc Based on Resistive Dac

Accumulatively Increasing Sensitivity of Ultrawide Instantaneous Bandwidth Digital Receiver with Fine Time and Frequency Resolution for Weak Signal Detection

Design of a 12-Bit 200 MS/s Time-Interleaved A/D Converter

Analog Front-End RX Design for UWB Impulse Radio in 90nm CMOS.

A 10-Bit 100-Mhz 70-Mw 2-Channel Time-Interleaved Pipelined ADC

Low-power 4 B 2 GHz Flash ADC for Ultra-Wideband Communications

A Second-Order Multi-Bit ΔΣ TDC for High Resolution IR-UWB Radar Systems