Abstract:This paper proposes a novel fault‐tolerant direct torque and flux control (DTFC) strategy to restrain fluctuating torque and enhance the torque dynamic performance of a five‐phase PMSM with open‐circuit fault. The decoupling control of torque and stator flux can be achieved under the open‐circuit fault condition, and the third harmonic current can be restrained without additional control. Multiphase permanent magnet synchronous motors (PMSMs) have attracted much more attention for their high efficiency, low torque ripple and good fault tolerance. However, open‐circuit fault results in asymmetrical motor behaviour, and deteriorates torque performance, especially dynamic response. This paper proposes a novel fault‐tolerant direct torque and flux control (DTFC) strategy to restrain fluctuating torque and enhance torque dynamic performance of a five‐phase PMSM with open‐circuit fault. The novelty of the proposed strategy is the development of DTFC based on stator flux orientation under the open‐circuit fault condition and the third harmonic current suppression with carrier‐based pulse width modulation technology. Consequently, the decoupling control of torque and stator flux can be achieved under the open‐circuit fault condition, and the third harmonic current can be restrained without additional control. Combined with deadbeat control, the heavy computation burden can be reduced. Thus, the proposed strategy not only can enhance torque dynamic performance under open‐circuit fault operation, but also keep smooth torque with circular stator flux trajectory before and after open‐circuit fault. The effectiveness of the proposed strategy is verified by the simulation and experimental results.

Computation-Efficient Solution to Open-Phase Fault Tolerant Control of Dual Three-Phase Interior PMSMs with Maximized Torque and Minimized Ripple

A Fault Tolerant Control Strategy for Dual Three-Phase PMSM under Single-Phase Open Circuit Fault Considering Inductance Asymmetry

Fault-Tolerant Control of Dual-Three-Phase PMSM under Open-Phase Fault Based on Two-Individual Current Control

Fault-Tolerant Operation for Single-Phase Open Circuit of Dual-Armature Flux-Switching Permanent Magnet Machine by Connecting Neutral Points

Optimized Fault-Tolerant Control of Dual Three-Phase PMSM Under Open-Switch Faults

Fault-Tolerant Control of Dual Three-Phase PMSM Based on Minimum Copper Loss under Multi-Phase Open and Open-Switch Faults

Analysis and Fault-Tolerant Control for Dual-Three-Phase PMSM Based on Virtual Healthy Model

Single- and Two-Phase Open-Circuit Fault Tolerant Control for Dual Three-Phase PM Motor Without Phase Shifting

Adaptive Torque Ripple Suppression Methods of Three-Phase PMSM During Single-Phase Open-Circuit Fault-Tolerant Operation

Control of Dual Three-Phase Permanent Magnet Synchronous Motor under Open Phase Fault Conditions

Torque dynamic performance enhancement of five‐phase permanent magnet synchronous motor with open‐circuit fault

Strategies for the fault-tolerant current control of a multiphase machine under open phase conditions

A Generalized Open-Circuit Fault-Tolerant Control Strategy for FOC and DTC of Five-Phase Fault-Tolerant Permanent-Magnet Motor

Fault Tolerant Control of Harmonic Injected Nine-Phase Flux Switching Permanent Magnet Motor Drive System

Fault Tolerant Control of a Multiphase Motor with Non-Sinusoidal Source under Open-Phase Conditions

Short-Circuit Fault-Tolerant Control Without Constraint on the D-Axis Armature Magnetomotive Force for Five-Phase PMSM

Fault-Tolerant Direct Torque Control of Five-Phase Permanent Magnet Synchronous Motor under Single Open-Phase Fault Based on Virtual Vectors

Open-Circuit Fault-Tolerant Control for Dual Three-Phase PMSM with Minimum Torque Ripple Considering Phase Back EMF Harmonics

Fault-Tolerant Control Strategy for Five-Phase PMSM with Third-Harmonic Current Injection

Single-phase Open-circuit Fault-tolerant Control for a Dual Five-phase Permanent Magnet Motor with Multi-operational Modes

Fault-tolerant Control of DTP-PMSM Based on Voltage Compensation