Abstract:Replacing ordinary concrete in partially encased concrete (PEC) columns with high-strength and durability reactive powder concrete (RPC) significantly improves their axial capacity and suppresses local buckling of the steel section. To study the axial mechanical performance of partially encased composite reactive powder concrete (PEC-RPC) columns after exposure to high temperatures, axial compression tests of eight PEC-RPC column specimens were designed and conducted. Thermal response, failure modes, axial load-vertical displacement curves, and strain-axial strain curves of different specimens were observed considering the effects of link spacing, cross-sectional dimensions, constant temperature duration, and cooling methods. Results indicate: PEC-RPC columns exhibited whitening on the surface of RPC after high-temperature exposure, specimens with the largest link spacing experienced RPC peeling due to concentrated thermal stress, exacerbated by spraying water, which created a stress difference between the surface and the interior, resulting in RPC peeling. The deeper the thermocouple was embedded, the lower the measured temperature. Additionally, due to the significantly lower thermal conductivity of RPC compared to steel, the temperature at measurement points within the RPC is much lower than that at the steel web. The failure mode of PEC-RPC columns after axial loading was characterized by the crushing of RPC and local buckling of section steel. The larger the link spacing, the more prone it was to multi-layer buckling, and columns with larger cross-sectional sizes tended to exhibit shear failure. The characteristic value of mechanical performance showed higher sensitivity to cross-sectional dimensions, but relatively lower sensitivity to link spacing and constant temperature duration. As the cross-sectional dimensions increased from 150×150 mm to 250×250 mm, the peak load, residual bearing capacity, stiffness, and ductility increased by 72.51–164.86 %, 89.8–173.6 %, 61.85–151.47 %, and 13.72–31.46 %, respectively. Finally, based on partition constraint theory and superposition principle, a simplified method for calculating the axial mechanical performance of PEC-RPC columns after exposure to high temperatures was proposed.

Factors Governing the Fire Response of Reactive Powder Concrete Simply-Supported Beams

Experimental Research the Shearing Performance of Grading-Fiber Reinforced Reactive Powder Concrete

Fire Resistance and Bending Bearing Capacity of Fire-Resistant Steel-Concrete Composite Beams

Modeling the Fire Response of Reactive Powder Concrete Beams with Due Consideration to Explosive Spalling

Experimental research on seismic behavior of concrete-filled reactive powder concrete tubular columns

Fire?resistance performance of simply supported fire?resistant steel?concrete composite beams

Experimental Study on the Spalling Strength of Fiber Reactive Powder Concrete

Effect of Fibers on High-Temperature Mechanical Behavior and Microstructure of Reactive Powder Concrete

RESEARCH ON BEHAVIOR OF STEEL REINFORCED CONCRETE (SRC) BEAMS IN FIRE

Modeling the Behavior of Insulated FRP-Strengthened Reinforced Concrete Beams Exposed to Fire

Experimental Investigation and Numerical Simulation on the Blast Resistance of Reactive Powder Concrete Subjected to Blast by Embedded Explosive

Fire Behavior of Full-Scale Cfrp-Strengthened Rc Beams Protected with Different Insulation Systems

Ultimate Bearing Capacity of Steel-Reactive Powder Concrete Composite Beams

Finite Element Modeling of Reinforced Concrete Beams Exposed to Fire

Fire Resistance of Reinforced Concrete Beams: A Three-Dimensional Finite Element Model

Experimental and Numerical Study on the Performance of Steel-Coarse Aggregate Reactive Powder Concrete Composite Beams with Uplift-Restricted and Slip-Permitted Connectors under Negative Bending Moment

Numerical analysis on mechanical behavior of steel‐concrete composite beams under fire

Numerical Simulation of Steel-Reinforced Reactive Powder Concrete Beam Based on Bond-Slip

Axial compressive behavior of partially encased composite reactive powder concrete columns after high-temperature exposure

Nonlinear Analysis of Insulated Carbon Fiber Reinforced Polymer Strengthened Reinforced Concrete Beams in Fire

Fire Resistance of RC Beams under Design Fire Exposure