Abstract:The mechanical anisotropic properties of aluminum alloy are studied using multi-level approaches for strain-rate and temperature-sensitive large plastic deformation of polycrystalline aggregates. Unlike previous researches, the thermal effect and the damage evolution process are considered simultaneously and integrated in the CPFEM method. In the microscopic constitutive equation of crystal plasticity, the shear strain rate on the slip system is described by an advanced exponential function based on thermal activated mechanism, instead of traditional phenomenological power-law function. To determine the rate-sensitive material parameters in this new model, the strain rate and temperature jump tests are performed. In addition, a simulation of one representative volume element is compared to the results of conventional tensile tests to obtain other thermal parameters. Coupled with the continuum damage evolution formula, this thermal affected crystal plasticity model is then implemented in a single crystal analysis for different orientation, temperature and strain rate conditions. Finally, this extended crystal plasticity model is applied in the finite element method to simulate the mechanical properties of 5052 aluminum alloy at absolute temperature 473 K. Taylor model is also used to compare these simulations as well as the experimental data. The results show that the damage model coupled in the crystal plasticity is able to predict the mechanical response of 5052 aluminum alloy; moreover, this model can simulate the explicit evolution of damage factor and local stress concentration in the deformation of standard tensile test specimen. In the simulation, the specimen is meshed by rectangular elements and each element is given an initial orientation at the first time increment step. This study argues that even in high temperature, the orientation mismatch between adjacent grains could lead to early cavity or crack initiation and the damage development is similar to the void evolution theory. An explanation of the possible fracture angle is given in the thermal tensile test due to polycrystalline anisotropy. At last, the analysis of stress heterogeneity and texture evolution is also shown in this study.

Crystal Plasticity Finite Element Modeling of Necking of Pure Aluminum During Uniaxial Tensile Deformation

Crystal Plasticity Modeling of Texture Evolution and Heterogeneity in Equal Channel Angular Pressing of Aluminum Single Crystal

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling.

Crystal Anisotropy of AZ31 Magnesium Alloy under Uniaxial Tension and Compression

Crystal Plasticity Finite Element Method for Slip Systems Evolution Analysis of / Duplex Titanium Alloys during Quasi-Static Tensile Testing

Crystal Plasticity Investigation of Friction Effect on Texture Evolution of Al Single Crystal During ECAP

Crystal plasticity extended models based on thermal mechanism and damage functions: Application to multiscale modeling of aluminum alloy tensile behavior

Heterogeneous Deformation and Damage Mechanisms in Multi-Phase TA15 Ti-alloy: Insights from Experiments Informed Damage-Crystal Plasticity Modelling

Plasticity and Deformation Mechanisms of Ultrafine-Grained Ti in Necking Region Revealed by Digital Image Correlation Technique

Crystal Plasticity Finite Element Method for Slip Systems Evolution Analysis of α/β Duplex Titanium Alloys during Quasi-Static Tensile Testing

Study of Slip-band of Crystalline Grains on the Surface of Polycrystalline Tensile Specimen

On the Tension Necking of Copper Single Crystal Specimen under Slip Deformation Mechanism

Constitutive Modeling of Slip, Twinning and Detwinning for Mg Alloy and Inhomogeneous Evolution of Microstructure

Crystal Plasticity Investigation of Texture Evolution of Al Single Crystal During Extrusion Through a Bent Channel

Influence of Defects and Crystallographic Orientation on Mechanical Behavior of Nanocrystalline Aluminium

The Study of Tension/Compression Asymmetry of [111] Oriented Nickel Base Single Crystal Superalloys

Crystal Plasticity Extend FEM Implementation of Thermal-Tensile Aluminum Alloy

Crystal plasticity modeling of deformation behavior of Al–Al2Cu eutectics based on high-fidelity representative microstructures

Crystal Plasticity Finite Element Simulation Study on Thread Rolling Pure Aluminum

Simulation of Texture Evolution During Plastic Deformation of FCC, BCC and HCP Structured Crystals with Crystal Plasticity Based Finite Element Method

A crystal plasticity-based microdamage model and its application on the tensile failure process analysis of 7075 aluminum alloy