Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes ( d ̄ ) were used for two-stage tensile tests under the conditions with distinct pre-strain εpre and intersection angle θSPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing εpre and θSPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d ̄ . This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre-strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Crystal Plasticity Modeling of Texture Evolution and Heterogeneity in Equal Channel Angular Pressing of Aluminum Single Crystal

Mechanical response and texture evolution prediction of AZ31 magnesium alloy during CVCDE process using crystal plasticity finite element method

Analysis of the texture evolution during multipass tube spinning of a TA15 alloy using the crystal plasticity finite element model

Ebsp Investigation of Microstructure and Texture Evolution During Equal Channel Angular Pressing of Aluminium

Crystal Plasticity Finite Element Simulation Study on Thread Rolling Pure Aluminum

Crystal plasticity modeling of deformation behavior of Al–Al2Cu eutectics based on high-fidelity representative microstructures

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Mechanical responses, texture and microstructural evolution of high purity aluminum deformed by equal channel angular pressing

Combining crystal plasticity and phase field model for predicting texture evolution and the influence of nuclei clustering on recrystallization path kinetics in Ti-alloys

Multiscale Mechanical Behavior and Microstructure Evolution of Extruded Magnesium Alloy Sheets: Experimental and Crystal Plasticity Analysis

Microstructure Evolution in High Purity Aluminum Single Crystal Processed by Equal Channel Angular Pressing (ECAP)

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

Predicting the in-plane mechanical anisotropy of 7085 aluminum alloys through crystal plasticity simulations and machine learning

Effect mechanism of texture orientation on mechanical properties and Hall-Petch relationship of CVCDE AZ31 magnesium alloy via crystal plastic finite element method (CPFEM)

In-situ EBSD Study of the Active Slip Systems and Lattice Rotation Behavior of Surface Grains in Aluminum Alloy During Tensile Deformation

Electrical-thermal-mechanical coupled modeling and simulation on deformation behaviors of Ti6554 alloy in electrically-assisted micro-tension

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

Crystal plasticity modelling of multi-stage deformation of ultra-thin sheets considering grain size effect and strain path change

An innovation in finite element simulation via crystal plasticity assessment of grain morphology effect on sheet metal formability

Texture modification and mechanical properties of AZ31 magnesium alloy sheet subjected to equal channel angular bending