Abstract:Solar cells have attracted much attention since they can convert solar energy directly into electricity, and have been widely utilized in manufacturing industry and people's daily life. Although the power conversion efficiency (PCE) of single-junction solar cells has gradually improved in recent years, its maximum efficiency is restricted by the Shockley-Queisser (SQ) limit of single-junction solar cells. To exceed the SQ limit and further obtain high efficiency solar cells, researchers have proposed the concept of tandem solar cells. In this work, a systematic theoretical study of chalcopyrite CuGaSe 2 /CuInSe 2 tandem solar cells was carried out by combining first-principle calculations and SCAPS-1D device simulations. Firstly, the electronic structure, defect properties and corresponding macroscopic performance parameters of CuGaSe 2 (CGS) were obtained by first-principles calculations, which were adopted as input parameters for subsequent device simulations of CGS solar cells. Subsequently, the simulations of single-junction CGS and CuInSe 2 (CIS) solar cells were carried out using SCAPS-1D software, respectively. The simulation results for the single junction CIS solar cells are in good agreement with the experimental values. For single-junction CGS cells, the device simulations revealed that CGS single-junction solar cells had the highest short-circuit current (J sc ) and PCE at the growth condition of Cu-rich, Ga-rich and Se-poor chemical growth condition. Further optimization found that the open-circuit voltage (V oc ) and PCE of CGS solar cells can be improved by replacing the electron transport layer (ETL) with ZnSe after the devices with the highest short-circuit current (J sc ). Finally, after the optimized CGS and CIS solar cells were connected in series with two-terminal (2T) monolithic tandem solar cell, the device simulation results show that under the growth temperature of 700 K and the growth environment of Cu-rich, Ga-rich, and Se-poor, with ZnSe as the ETL, the CGS thickness of 2000 nm and the CIS thickness of 1336 nm, the PCE of 2T monolithic CGS/CIS tandem solar cell can reach 28.91 %, which is higher than the recorded efficiency of the current single-junction solar cells, and shows a good application prospect.

All Antimony Chalcogenide Tandem Solar Cell

Sb2Se3 as a bottom cell material for efficient perovskite/Sb2Se3 tandem solar cells

Perovskite/Colloidal Quantum Dot Tandem Solar Cells: Theoretical Modeling and Monolithic Structure

Exploring the potential of standalone and tandem solar cells with Sb2S3 and Sb2Se3 absorbers: a simulation study

Toward high-efficiency solution-processed tandem solar cells

Theoretical Insight into High‐Efficiency Triple‐Junction Tandem Solar Cells via the Band Engineering of Antimony Chalcogenides

Design and analysis of Sb2S3/Si thin film tandem solar cell

Gradient bandgap modification for highly efficient carrier transport in antimony sulfide-selenide tandem solar cells

All-inorganic Sb2S3-based Two-terminal Tandem Solar Cells Enable over 10.9% Efficiency Employing a Concise Interconnection Layer

Development of Antimony Sulfide–selenide Sb2(S, Se)3-based Solar Cells

Proposal and Numerical Analysis of Organic/Sb2Se3 All-Thin-Film Tandem Solar Cell

Simulations of Chalcopyrite/c-Si Tandem Cells Using SCAPS-1D

Effects of Subcell Bandgap Matching on the Performance of Perovskite/cu(in,ga)se2 Tandem Solar Cells

Bifacial and Semitransparent Sb2(S,Se)3 Solar Cells for Single‐Junction and Tandem Photovoltaic Applications

Concurrent investigation of antimony chalcogenide (Sb2Se3 and Sb2S3)-based solar cells with a potential WS2 electron transport layer

HTL-Free Sb 2 (S, Se) 3 Solar Cells with an Optimal Detailed Balance Band Gap

CuIn(Se,Te)2 absorbers with bandgaps < 1 eV for bottom cells in tandem applications

Over 7% Efficiency of Sb2(S,Se)3 Solar Cells Via V‐Shaped Bandgap Engineering

Top cell design and optimization of all-chalcopyrite CuGaSe 2 /CuInSe 2 two-terminal tandem solar cells: first-principles calculations and device simulations

Monolithic Two-Terminal Tandem Solar Cells Using Sb 2 S 3 and Solution-Processed PbS Quantum Dots Achieving an Open-Circuit Potential beyond 1.1 V

Vapor Transport Deposition of Sb 2 (S,Se) 3 Solar Cells with Continuously Tunable Band Gaps