Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

Grain Boundary Feature and Its Effect on Mechanical Property of Ni 690 Alloy Layer Produced by GTAW

Grain Boundary Carbides Evolution and Their Effects on Mechanical Properties of Ni 690 Strip Weld Metal at Elevated Temperature

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of Grain Boundary Behaviour on Ductility Dip Cracking Mechanism

Improve the ductility of a nickel based superalloy by optimizing secondary phase distribution through grain boundary engineering

Damage Tolerance of Low Angle Grain Boundary in a Fourth Generation Nickel-based Single Crystal Superalloy at 1100 °C Service Conditions

Influence of Heat Treatment Temperature on Grain Structures and Properties of a Ni-based Superalloy Fabricated Via Selective Laser Melting

Anisotropy in microstructure and mechanical properties of additively manufactured Ni-based GH4099 alloy

Effect of Welding Thermal Treatment on the Microstructure and Mechanical Properties of Nickel-Based Superalloy Fabricated by Selective Laser Melting

New insights into ductility improvement of a nickel-based superalloy through grain boundary engineering

Precipitation Behavior of Grain Boundary M23C6 and Its Effect on Tensile Properties of Ni–Cr–W Based Superalloy

Microstructure and Mechanical Properties of Tlp Diffusion Bonded Joint of Mgh956/Gh3230 Superalloy

An Investigation of the Microstructural Evolution and Tensile Properties of a Nickel-Based GH648 Superalloy Manufactured Through Selective Laser Melting

Fractal Analysis of Mo and Nb Effects on Grain Boundary Character and Hot Cracking Behavior for Ni-Cr-Fe Alloys

Research on Microstructure and Mechanical Properties of Square Wave Alternating Current Tungsten Inert Gas Welded Joints in 2219-T6 Aluminum Alloy

Effect of Rotation Speed on Microstructure Evolution and Mechanical Properties of Nugget Zone in 2195-T8 Al-Li Alloy Friction Stir Welding Joints

Microstructure and Mechanical Property of a Directional Ni-Based Superalloy During Long-Term Exposure

Influence of Various Heat Treatments on Microstructures and Mechanical Properties of GH4099 Superalloy Produced by Laser Powder Bed Fusion

Ultrasonic vibration assisted gas tungsten arc welding of Inconel 690 alloy: Ultrasonic effect to refine grains and improve mechanical properties

High-temperature mechanical properties and microstructure of welded joint in GH4169/IC10 dissimilar nickel-based superalloys by vacuum electron beam welding