Abstract:Following a decision made at the ITER Council in November 2013, two types of in-vessel coils (IVCs), namely, edge-localized mode (ELM) coils to mitigate ELMs and vertical stability (VS) coils to provide vertical stabilization of the plasma, have been incorporated in the ITER baseline design. The in-vessel environment is severe, characterized by large transient electromagnetic fields, high radiation flux, and high temperature. To withstand this environment and provide the required functionality, a "mineral insulated conductor" (MIC) technology has been selected for the IVC conductor. It consists of an axially water-cooled copper conductor surrounded by magnesium oxide insulation and a stainless steel jacket. A major advantage of the coil design is the choice of the same conductor material and dimensions for both VS and ELM coils, long conductor length which eliminates the need for any internal joints, and Cu welding for the joints between coils and feeders. In situ winding of the VS coils is asking for the development of a creative solution for the unspooling, straightening, precise winding tools, bending, forming, and metrology processes in a tight and congested environment. Mock-ups for design verification and manufacturing feasibility have been produced, in particular, for the bracket manufacture and to perform thermal and mechanical fatigue testing on an ELM control coil winding pack assembly. Installation trials of a half-size ELM control coil have been performed to verify the feasibility of the assembly procedure. This article will give an overview of the IVC design status and the progress of ITER IVC conductor manufacturing.

Nondestructive Evaluation of Eccentricity of Iter In-Vessel Coil Conductors Based on Pulsed Ect Method

Nondestructive Evaluation of Eccentricity of ITER In-Vessel Coils Based on Eddy Current Testing

Testing of Eccentricity in Tokamak In-vessel Coil Conductors

Eddy Current Testing of Eccentricity in Tokamak In-Vessel Coil Conductors Based on Flexible Probe

Eddy current test research for eccentricity of international thermonuclear experimental reactor (ITER) in-vessel coils (IVCs) conductor

Parameter Opitimization of Eddy Current Testing Probe for Evaluation of Eccentricity in Conductors of Tokamak In-Vessel Coils

Research on Nondestructive Examination of Bracket Welds of ITER In-Vessel Coils (IVC)

Developments of Nondestructive Test Method of Jacket Section for ITER Poloidal Field Coils

Developments of NDE Method of Jacket Welds for ITER In-Vessel Coil Joints

Fatigue Behavior Testing and Evaluation of ITER In-vessel Mock-Up Coil under Combined Thermal and Electromagnetic Loads

Development Of Insulation Technology With Vacuum-Pressure-Impregnation (Vpi) For Iter Correction Coil

Quantitative Nondestructive Estimation of Deep Defects in Conductive Structures

Lift-off Nulling and Internal State Inspection of Multi-Layer Conductive Structures by Combined Signal Features in Pulsed Eddy Current Testing

Optimization of Excitation Coil in Pulsed Eddy Current Testing of a Pipe Based on the Incident Field

Identification Of Wire Breakage Status Based On The Measurement And Inversion Of Magnetic Field Aiming At Applications To Cable In Conduit Conductors Of Iter Magnets

Research on Nondestructive Examination of Jacket Section for CFETR TF Coil

Eddy Current Pulsed Thermography with Different Excitation Configurations for Metallic Material and Defect Characterization.

Final Design of ITER In-Vessel Coils and Manufacturing of In-Vessel Coil Conductor

Proposal And Demonstration Of Strategies For Ndt Of Conduit Tube Of Cable In Conduit Conductors Used In Iter Pf Coils

A New Array Eddy Current Testing Probe for Inspection of Small-Diameter Tubes in Tokamak Fusion Devices

Quantitative Non-Destructive Evaluation of Wall Thinning Defect in Double-Layer Pipe of Nuclear Power Plants Using Pulsed Ect Method