Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

An Investigation on the Relationships Between Cohesive Energy Density and Tribological Properties for Polymer–polymer Sliding Combinations

Tribological Behaviors of Several Polymer–polymer Sliding Combinations under Dry Friction and Oil-Lubricated Conditions

Effect of Lubricating Condition on Tribological Properties of Nano-SiO2 Filled Polyamide Composite

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Influence of adhesive and abrasive mechanisms on the tribological behaviour of thermoplastic polymers

Anomalous Lubrication Behavior of Metal-Polymer Tribo-Pairs

Tribological characteristics of polymer materials used for slide bearings

Differences in Tribological Behaviors upon Switching Fixed and Moving Materials of Tribo-pairs including Metal and Polymer

An investigation of the wear of polymeric materials

COMPARATIVE STUDY ON THE FRICTION CHARACTERISTICS OF TWO POLYMERIC MATERIALS SLIDING INTO ENVIRONMENTS DRIED OR LUBRICATED WITH OIL

Mechanical and Tribological Properties of PA/PPS Blends

A review on tribology of polymer composite coatings

Comparative Evaluation of the Tribological Properties of Polymer Materials with Similar Shore Hardness Working in Metal–Polymer Friction Systems

Synergistic effects of carbon fiber and polytetrafluoroethylene on the friction and wear behavior of polyarylene ether nitrile under dry lubrication condition

Combination of a Viscoelastic and a Tribological Analysis of a Low Density Polyethylene with a High Degree of Crosslinking

Tribological Properties and Wear Mechanism of C/C Composite Applied in Finger Seal

Static friction of normal and reversed metal–polymer sliding pairs

Mechanical And Tribological Properties Of Paws Blends

Comparative Study of Tribological Properties of Polyphenylene Sulfide (PPS), Polyethersulfone (PES), and Polysulfone (PSU)

Effect of crystalline form on the tribological properties of PA46/HDPE polyblends

Study on tribological properties of frictional material based aromatic polyamide