Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Combination of a Viscoelastic and a Tribological Analysis of a Low Density Polyethylene with a High Degree of Crosslinking

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Preparation and characterization of polyethylene glycol/poly(L-lactic acid) blends

Viscoelastic Study of Single Chain Cyclized Polymeric Nanoparticles and Linear Polymers Blends

Mechanical and shape memory behavior of chemically cross-linked SBS/LDPE blends

Rheologic Studies on Chemical Cross-Linking Kinetics for LDPE

The effect of chemical crosslinking on the properties of Rotomolded high density polyethylene

Enhancing the Tribological Properties of Low-Density Polyethylene Using Hard Carbon Microfillers

Tribological Enhancement Effect of Main-Chain Thermotropic Liquid Crystalline Polymer

Influence of Crosslink Density on Electrical Performance and Rheological Properties of Crosslinked Polyethylene

Effect of crystalline form on the tribological properties of PA46/HDPE polyblends

The Effect of Dialkyl Peroxide Crosslinking on the Properties of LLDPE and UHMWPE

Thermal, mechanical, and dielectric behaviors of crosslinked linear low density polyethylene/polyolefin elastomers blends

Structure and Properties of Reactive Extruded Ethylene-Block-Co-Polypropylene: Influence of Dicumyl Peroxide and Divinylbenzene

INFLUENCE OF CROSSLINKING ON PHYSICAL PROPERTIES OF LOW DENSITY POLYETHYLENE

Study on Crosslinking of Polyethylene–Octene Elastomer with Dicumyl Peroxide

The effect of cross-linking system and reinforcement on the cross-linking reaction of peroxide vulcanized ethylene-propylene-diene terpolymer (EPDM) matrix

Dynamically photocrosslinking of polypropylene/EPDM blends as a thermoplastic elastomer

Effect of perfluoroalkylmethacrylate ester-grafted-linear low-density polyethylene on the tribological property of polyoxymethylene-linear low-density polyethylene composites

Effect of Partial Crosslinking on Morphology and Properties of the Poly(β-Hydroxybutyrate)/poly(d,l-lactic Acid) Blends