Abstract:A 1550 nm all-fiber dual-polarization coherent Doppler lidar (DPCDL) was constructed to measure the depolarization ratio of atmospheric aerosols. In lidar systems, the polarization state of the laser source is typically required to be that of linearly parallel polarization. However, due to the influence of the fiber-optical transmission and the large-mode field output of the telescope, the laser polarization state changes. Hence, a polarizer was mounted to the emitting channel of the telescope to eliminate the depolarization effect. A fiber-optical polarization beam splitter divided the backscattered light into components with parallel and perpendicular polarization. The DPCDL used two coherent channels to receive each of these two polarization components. A calibration procedure was designed for the depolarization ratio to determine the differences in gain and non-responsiveness in the two polarization channels. The calibration factor was found to be 1.13. Additionally, the systematic error and the measured random error of the DPCDL were estimated to evaluate the performance of the system. The DPCDL’s systematic error was found to be about 0.0024, and the standard deviation was lower than 0.0048. The Allan deviations of a 1-min averaging window with a low SNR of 19 dB and a high SNR of 27 dB were 0.0104 and 0.0031, respectively. The random errors at different measured heights were mainly distributed below 0.015. To confirm the authenticity of the atmospheric depolarization ratio measured with the DPCDL, two field observations were conducted with the use of a co-located DPCDL and micro-pulse polarization lidar to perform a comparison. The results showed that the correlation coefficients of the aerosol depolarization ratios were 0.73 and 0.77, respectively. Moreover, the two continuous observations demonstrated the robustness and stability of the DPCDL. The depolarization ratios were detected in different weather conditions.

Performance Validation on an All-Fiber 1.54-Μm Pulsed Coherent Doppler Lidar for Wind-Profile Measurement

Validation of airborne 1 . 5 μ m all-fiber coherent lidar measurement of wind profiles

All Fiber Pulsed Coherent Lidar Development for Wind Profiles Measurements in Boundary Layers

Performance Verification of Mobile Doppler Wind Lidar

Demonstration on the Performance Enhancement of the 1.645 Μm Coherent Doppler Lidar for Long-Range Wind Measurements with Modification of Laser Transmitter and Optical Antenna

1.55Μm All-Fiber Coherent Doppler Lidar for Wind Measurement

15 Μm Polarization Coherent Lidar Incorporating Time-Division Multiplexing

1.5 mu m polarization coherent lidar incorporating time-division multiplexing

A novel wind ladar system based on 1.55 mu m All-fiber Coherent

1.55-Μm Pulse Coherent LIDAR with 10-Km Detection Range

Calibration of FP Etalon Transmittance Curve and Wind Field Observation Based on Doppler Wind Measurement Lidar

Performance of Continuous-wave Coherent Doppler Lidar for Wind Measurement

Performance validation for wind measurement with multi-longitudinal mode double-edge detection

Research On Velocity Calibration Of An Eye-Safe All-Solid-State Coherent Doppler Wind Lidar

Analysis of Accuracy and Acquisition Rate of Doppler Lidar Multi-Beam Wind Measurement

Development and Experimental Testing of a Rotary Direct Wind Lidar System Based on Fabry.Perot Interferometer Technology-=SUP=-*-=/SUP=-

High efficiency all fiber coherent lidar for wind measurement

Scanning Rayleigh Doppler Lidar for Wind Profiling Based on Non-polarized Beam Splitter Cube Optically Contacted FPI

Research on optimizing the optical local-oscillator power of Coherent Doppler LiDAR to enhance wind velocity measurements

Fabry-Perot interferometer based Mie Doppler lidar for low tropospheric wind observation

The Design and Performance Evaluation of a 1550 Nm All-Fiber Dual-Polarization Coherent Doppler Lidar for Atmospheric Aerosol Measurements