Abstract:Rayleigh Doppler lidar based on a quad Fabry-Perot etalon (FPE) is proposed that is capable of accurately detecting wind speed, as well as temperature and aerosol from 0.2 to 60km altitude. The structure of lidar is designed and its measurement principle is analyzed. One of the four FPEs, i.e. FPE-L is used for locking and measuring the outgoing laser frequency, and the other three, i.e. FPE-1, -2 and -3 form a three-stage FPE. The first-stage FPE (FPE-1) can effectively filter out Mie backscattering signal, thereby suppressing its effects on wind measurement and measuring the aerosol backscatter ratio as well. The transmission spectra of the second- and third-stage FPEs (FPE-2,-3) form double edge for simultaneous wind and temperature measurements by using Rayleigh backscattering signal. The parameters of the quad FPE are optimized. The FWHM and relative peak position of FPE-1,-2,-3,-L are 0.6, 1.2, 1.2, 0.6GHz and 0, -1, 1, 0.3GHz, respectively. The performance of the proposed lidar is simulated and results show that for 0.3WSr-1m-2nm-1@355nm sky brightness, by using a 350mJ pulse energy, 50Hz repetition frequency laser and a 0.8m aperture telescope, with temporal resolution of ∼20km, ∼60km and vertical resolution of ∼10km, ∼ 20km, ∼40km, ∼60km, the measurement errors of temperature, aerosol backscattering ratio and vertical wind speed are below 5.3K, 3.0×10-3, 1.1m/s in nighttime and below 14.6K, 8.1×10-3, 2.5m/s in daytime from 0.2 to 60km altitude; the measurement error of two other orthogonal LOS wind speed with fixed zenith angle of 25.8° is below 1.3m/s in nighttime and 3.5m/s in daytime within the LOS wind speed dynamic range of ±50m/s from 0.2 to 60km altitude.

All Fiber Pulsed Coherent Lidar Development for Wind Profiles Measurements in Boundary Layers

1.55-Μm Pulse Coherent LIDAR with 10-Km Detection Range

A novel wind ladar system based on 1.55 mu m All-fiber Coherent

1.55Μm All-Fiber Coherent Doppler Lidar for Wind Measurement

Doppler Wind Lidar Based on Fabry-Perot Etalon

Performance of Continuous-wave Coherent Doppler Lidar for Wind Measurement

A Novel Wind Ladar System Based on 1.55μm All-Fiber Coherent Doppler Laser

Polarized High-Spectral-Resolution Lidar Based on Field-Widened Michelson Interferometer

Fabry-Perot interferometer based Mie Doppler lidar for low tropospheric wind observation

Multi-Longitudinal-Mode High-Spectral-Resolution Lidar

Micro-pulse upconversion Doppler lidar for wind and visibility detection in the atmospheric boundary layer

Direct Detection Doppler Wind Lidar Based on Dual FP Etalon

Scanning Rayleigh Doppler Lidar for Wind Profiling Based on Non-polarized Beam Splitter Cube Optically Contacted FPI

All-fiber Upconversion High Spectral Resolution Wind Lidar Using a Fabry-Perot Interferometer

Quad-Fabry-Perot etalon based Rayleigh Doppler lidar for 0.2-60km altitude wind, temperature and aerosol accurate measurement

Data Processing and Analysis of Eight-Beam Wind Profile Coherent Wind Measurement Lidar

Design and performance simulation of 532 nm Rayleigh–Mie Doppler lidar system for 5–50 km wind measurement

Pulse Accumulation Approach Based on Signal Phase Estimation for Doppler Wind Lidar

Mid-altitude wind measurements with mobile Rayleigh Doppler lidar incorporating system-level optical frequency control method

A Pulsed-Coherent Lidar With Sub-10 μm Precision

Real-Time Synchronous Acquisition and Processing of Signal in Coherent Doppler Wind Lidar Using FPGA