Abstract:A novel Rayleigh Doppler lidar technology based on a quadruple dual-pass Fabry–Perot interferometer (FPI) that can accurately measure wind field, temperature and aerosol backscatter ratio from the troposphere to lower stratosphere is proposed. This study aims to analyse the detection principle of wind speed, temperature and aerosol backscatter ratio in detail and obtain their measurement error formulas. The structure of this type of lidar is studied and designed. The FPI consists of two edge channels FPI-1 and FPI-2, aerosol channel FPI-M and locking channel FPI-L. FPI-1, FPI-2 and FPI-M use a dual-pass optical path, whereas FPI-L uses a single-pass optical path. The parameters of FPI are optimised as follows: the free spectral spacing (FSR) is 12 GHz, the FWHM of FPI-1 and FPI-2 are both 2.2 GHz, the peak-to-peak interval of FPI-1 and FPI-2 is 5.8 GHz, the FWHM of FPI-M and FPI-L are both 1.2 GHz, the peak-to-peak interval of FPI-M and FPI-1 is 2.9 GHz and the peak-to-peak interval of FPI-L and FPI-1 is 2.3 GHz. Under simulated atmospheric conditions, for a daytime sky background brightness of 0.3 Wsr −1 m −2 nm −1 at 355 nm, using a laser with a pulse energy of 350 mJ and a repetition frequency of 50 Hz and a telescope with a 0.45-m aperture, with a vertical range resolution of 30 m at 0–10 km, 100 m at 10–20 km and 500 m at 20–35km, temporal resolution of 30 min, zenith angle of 0° for temperature and aerosol backscatter ratio detection and temporal resolution of 3 min and zenith angle of 30° for radial wind speed detection, the detection performance of the designed Rayleigh Doppler lidar is determined. The simulation results show that the measurement errors of aerosol backscatter ratio, temperature and radial wind speed of the lidar system in the daytime and night-time are less than 4.36 × 10 −3 and 3.32 × 10 −3 (excluding cirrus cloud area), 4.0 K and 3.0 K and 3.8 m/s and 1.9 m/s, respectively, from an altitude of 0.06 to 35km.

Doppler Wind Lidar Based on Fabry-Perot Etalon

Direct Detection Doppler Wind Lidar Based on Dual FP Etalon

Quad-Fabry-Perot etalon based Rayleigh Doppler lidar for 0.2-60km altitude wind, temperature and aerosol accurate measurement

Fabry-Perot interferometer based Mie Doppler lidar for low tropospheric wind observation

High-spectral-resolution Mie Doppler lidar based on a two-stage Fabry–Perot etalon for tropospheric wind and aerosol accurate measurement

Analysis of data processing method for Doppler wind lidar

Rayleigh Doppler Lidar Technology Based on a Quadruple Dual-pass Fabry–Perot Interferometer

Multi-Longitudinal-Mode High-Spectral-Resolution Lidar

1.55Μm All-Fiber Coherent Doppler Lidar for Wind Measurement

A novel wind ladar system based on 1.55 mu m All-fiber Coherent

A Novel Wind Ladar System Based on 1.55μm All-Fiber Coherent Doppler Laser

All-fiber Upconversion High Spectral Resolution Wind Lidar Using a Fabry-Perot Interferometer

Polarized High-Spectral-Resolution Lidar Based on Field-Widened Michelson Interferometer

Micro-pulse upconversion Doppler lidar for wind and visibility detection in the atmospheric boundary layer

Performance of Continuous-wave Coherent Doppler Lidar for Wind Measurement

Beam Scanning and Wind Field Measurement of Direct-Detection Doppler Lidar

Mobile Rayleigh Doppler lidar for wind and temperature measurements in the stratosphere and lower mesosphere

Data Processing and Analysis of Eight-Beam Wind Profile Coherent Wind Measurement Lidar

Design and performance simulation of 532 nm Rayleigh–Mie Doppler lidar system for 5–50 km wind measurement

Scanning Rayleigh Doppler Lidar for Wind Profiling Based on Non-polarized Beam Splitter Cube Optically Contacted FPI

Mid-altitude wind measurements with mobile Rayleigh Doppler lidar incorporating system-level optical frequency control method