Abstract:Self‐assembly and nonsolvent‐induced phase separation (SNIPS) of block copolymers and solvents enable the fabrication of integral‐asymmetric, isoporous membranes. Using large‐scale particle simulations, the dependence of the membrane morphology on structural, thermodynamic (e.g., incompatibility between matrix‐forming block and nonsolvent), kinetic (e.g., vitrification threshold), and process parameters (e.g., duration of EISA) is predicted. Examining the top layer and substructure, the findings are verified through experiment. The self‐assembly and nonsolvent‐induced phase separation (SNIPS) process of block copolymers and solvents enables the fabrication of integral‐asymmetric, isoporous membranes. An isoporous top layer is formed by evaporation‐induced self‐assembly (EISA) and imparts selectivity for ultrafiltration of functional macromolecules or water purification. This selective layer is supported by a macroporous bottom structure that is formed by nonsolvent‐induced phase separation (NIPS) providing mechanical stability. Thereby the permeability/selectivity tradeoff is optimized. The SNIPS fabrication involves various physical phenomena—e.g., evaporation, self‐assembly, macrophase separation, vitrification – and multiple structural, thermodynamic, kinetic, and process parameters. Optimizing membrane properties and rationally designing fabrication processes is a challenge which particle simulation can significantly contribute to. Using large‐scale particle simulations, it is observed that 1) a small incompatibility between matrix‐forming block of the copolymer and nonsolvent, 2) a glassy arrest that occurs at a smaller polymer concentration, or 3) a higher dynamical contrast between polymer and solvent results in a finer, spongy substructure, whereas the opposite parameter choice gives rise to larger macropores with an elongated shape. These observations are confirmed by comparison to experiments on polystyrene (PS)‐block‐poly(4‐vinylpyridine) (P4VP) diblock copolymer membranes, varying the chemical nature of the coagulant or the temperature of coagulation bath.

Computer Simulations on Double Hydrophobic PS-b-PMMA Porous Membrane by Non-Solvent Induced Phase Separation

Effect of solvent concentration on development of macrovoids of PVDF phase-diversion membranes

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Preparation of Porous PVDF Membrane Via Thermally Induced Phase Separation with Diluent Mixture of DBP and DEHP

Fabrication of Hydrophilic and Sponge-Like PVDF/brush-like Copolymer Blend Membranes Using Triethylphosphate As Solvent

Dissipative Particle Dynamics Simulation on the Membrane Formation of Polymer–solvent System Via Nonsolvent Induced Phase Separation

Dissipative Particle Dynamics Simulation of the Effect of Polymer Chain Rigidity on Membranes Formation by Nonsolvent Induced Phase Separation Process

Dissipative Particle Dynamics Study and Experimental Verification on the Pore Morphologies and Diffusivity of the Poly (4-Methyl-1-pentene)-diluent System Via Thermally Induced Phase Separation: the Effect of Diluent and Polymer Concentration

Novel multiscale simulations on the membrane formation via hybrid induced phase separation process based on dissipative particle dynamics

Solvent-Induced Morphology of the Binary Mixture of Diblock Copolymer in Thin Film: the Block Length and Composition Dependence of Morphology

Investigation on the membrane formation process of polymer–diluent system via thermally induced phase separation accompanied with mass transfer across the interface: Dissipative particle dynamics simulation and its experimental verification

Multiscale Simulation on the Membrane Formation Process Via Thermally Induced Phase Separation Accompanied with Heat Transfer

Preparation and Characterization of Microporous PVDF Membrane by Thermally Induced Phase Separation from a Ternary Polymer/solvent/non-Solvent System

Symmetrical Permeable Membranes Consisting of Overlapped Block Copolymer Cylindrical Micelles for Nanoparticle Size Fractionation

Microphase Separation Behavior on the Surfaces of Poly(Dimethylsiloxane)-Block-Poly(2,2,3,3,4,4,4-Heptafluorobutyl Methacrylate) Diblock Copolymer Coatings

Computer simulation and experimental verification of morphology and gas permeability of poly(4-methyl-1-pentene) membranes: effects of polymer chain and diluent extractant

Surface Microphase Separation in PDMS‐b‐PMMA‐b‐PHFBMA Triblock Copolymer Films

Microphase Separation of Diblock Copolymer Poly(styrene-B-isoprene): A Dissipative Particle Dynamics Simulation Study

Toward Predicting the Formation of Integral‐Asymmetric, Isoporous Diblock Copolymer Membranes

Three-dimensional analysis of membrane formation via thermally induced phase separation by dissipative particle dynamics simulation

Preparation of Polyethylene Microporous Membranes with High Water Permeability from Thermally Induced Multiple Phase Transitions