Abstract:The upper and lower parts of the figure show the phase diagrams, molecular migration process, membrane formation driving force, and the final membrane structures involved in the RTIPS and NIPS methods, respectively. When the solidification bath temperature is greater than the cloud point temperature and exceeds the critical concentration, the undesirable interaction between PSE and DEG dominates the casting solution system, which leads to the enrichment of DEG to complete the phase separation, and the driving force for membrane formation is the temperature difference, which ultimately results in the formation of a homogeneous sponge pore structure; when the solidification bath temperature is lower than the cloud point temperature, the mixed solvents are exchanged with water, and the driving force for membrane formation is the osmotic pressure, which ultimately results in the formation of a finger‐like structure. Contaminated water sources from various industries pose severe environmental challenges due to their complex compositions, high toxicity, and fluctuating qualities. This study introduces a groundbreaking strategy for fabricating advanced polysulfate (PSE) ultrafiltration membranes using a novel reverse thermally induced phase separation (RTIPS) process. By manipulating the cloud point through the DMAc/DEG solvent/nonsolvent system, our work innovatively controls membrane microstructure, overcoming limitations of conventional nonsolvent‐induced phase separation (NIPS). Our findings reveal that RTIPS, when employed above the cloud point, yields PSE membranes with a unique bicontinuous sponge‐like structure, significantly improving upon conventional NIPS products. Specifically, the optimized RTIPS membranes exhibit enhanced pure water flux (916.23 vs. 336.23 LMH), larger pore sizes (0.083 vs. 0.054 μm), increased tensile strength (1.32 vs. 0.84 MPa), and improved fouling resistance (FRR 65.5% vs. 55.2%). This research pioneers a facile yet potent method for tailoring membrane properties, achieving a balance between permeability, mechanical stability, and filtration efficacy. The demonstrated success of RTIPS in enhancing PSE membrane performance not only contributes to the development of high‐performance water treatment technologies but also charts a new course in membrane science, offering a promising avenue for sustainable wastewater management solutions.

Anti-pollution Polyethersulfone/sulfonated Polysulfone (pes/spsf) Membrane with Different Sulfonation Degree by Reverse Thermally Induced Phase Separation (RTIPS) Procedure

Preparation and Characterization of Polyethersulfone Microporous Membrane Via Thermally Induced Phase Separation with Low Critical Solution Temperature System

A Facile Way to Prepare Hydrophilic Homogeneous PES Hollow Fiber Membrane Via Non-Solvent Assisted Reverse Thermally Induced Phase Separation (RTIPS) Method

Exploring of novel reverse thermally induced phase separation process based on preparation and characterization of polysulfate ultrafiltration membranes with bicontinuous structure

A Polyethersulfone–bisphenol Sulfuric Acid Hollow Fiber Ultrafiltration Membrane Fabricated by a Reverse Thermally Induced Phase Separation Process

Preparation and characterization of PES/CA microporous membranes via reverse thermally induced phase separation process

Investigating the Impact of the Sulfonation Degree in Sulfonated Polyphenylsulfone (sPPSU) on PES/sPPSU Polymer Blend Membranes

Bimetallic polyphenol networks structure modified polyethersulfone membrane with hydrophilic and anti-fouling properties based on reverse thermally induced phase separation method

Fabricating PES/SPSF membrane via reverse thermally induced phase separation (RTIPS) process to enhance permeability and hydrophilicity

A Novel PES-TiO2 Hollow Fiber Hybrid Membrane Prepared Via Sol-Gel Process Assisted Reverse Thermally Induced Phase Separation (RTIPS) Method

Development of hydrophilic PES membranes using F127 and HKUST-1 based on the RTIPS method: Mitigate the permeability-selectivity trade-off

Polysulfone Membranes Via Thermally Induced Phase Separation

Microporous Polyethersulfone Membranes Prepared under the Combined Precipitation Conditions with Non-Solvent Additives

Preparation Of Micro-Porous Polyethersulphone Hollow Fibre Membranes Using Non-Solvent Vapour-Induced Phase Separation

Novel polysulfone hybrid ultrafiltration membrane prepared with TiO2-g-HEMA and its antifouling characteristics

Effect of Different Solvents, Pore-Forming Agent and Solubility Parameter Differences on the Properties of PES Ultrafiltration Membrane

Preparation and Performance of Polyethersulfone Hollow-Fiber Membrane

Superhydrophilic polyethersulfone (PES) membranes with high scale inhibition properties obtained through bionic mineralization and RTIPS

Facile membrane preparation strategy to reinforce permeability of polyethersulfone (PES) micro-ultrafiltration membrane for drinking water treatment

Estimation of Phase Separation Temperatures for Polyethersulfone/solvent/non-Solvent Systems in RTIPS and Membrane Properties

Preparation and characterization of an antifouling poly (phenyl sulfone) ultrafiltration membrane by vapor-induced phase separation technique