Abstract:The thermal deformation behavior of oxidation products formed on Fe–Si alloys with varying Si contents was systematically investigated using a thermal simulation testing machine during compressive deformation at temperatures ranging from 800 to 1100 °C. It is found that the higher the deformation temperature is, the better the plasticity of the oxide product is, and the better the deformation coordination between the oxidation product and the substrate, where the deformation mainly occurs in the FeO layer. The increase of Si content reduces the coordination of deformation between the oxidation product and the substrate, but it can improve the interface straightness. The crystal structure of the oxidation product determines its plastic deformation ability, and the deformation mechanism of FeO is determined by the dislocation slip and climb, and its plastic deformation ability is the best. The dislocation slip dominates the deformation mechanism of Fe 3 O 4 , and the deformation ability is the second, and Fe 2 O 3 has basically no plastic deformation ability. Therefore, the increase of the Si content leads to the reduction of the proportion of the FeO layer in the oxidation product, which is the main reason for the decrease of the deformation coordination between the oxidation product and the substrate. As Si element forms a spinel solid solution composed of Fe 2 SiO 4 with FeO and SiO 2 at the interface, it has good plastic deformation ability and can deform synchronously with the substrate, and the porous structure can effectively relieve the compressive stress during deformation, which can effectively improve the interface straightness. In addition, the increase of Si content makes the concentration of iron ions in FeO close to the substrate side lower, which causes the increase of point defect concentration to promote the dislocation climbing of FeO, and makes the steady-state plastic deformation ability of FeO close to the substrate side higher, which improves the straightness of the interface between the oxidation product and the substrate.

Study on the Interfacial Reactions Between an Fe–Mn–Si Alloy and Complex Oxides Containing FeO During Isothermal Heating

The Influence of FeO on the Reaction between Fe–Al–Ca Alloy and Al2O3–CaO–FeO Oxide during Heat Treatment at 1473 K

Evolution of Interfacial Features of MnO-SiO2 Type Inclusions/Steel Matrix during Isothermal Heating at Low Temperatures

Investigation of Selective Oxidation During Cooling of Hot-Rolled Iron-Manganese-silicon Alloys

Influence of Mn–Si elements on the kinetics of oxidative phase transformation under continuous cooling conditions and modeling study

Effect of Si Content and Temperature on Oxidation Resistance of Fe-Si Alloys

Oxidation behavior of AlCoCrFeNiSi high-entropy alloys at 1100 °C

Study on the high-temperature oxidation of AlCrFeCoNi-based high-entropy alloys with trace Si additions

Morphology, thermal stability, electronic structure and mechanical properties of α-AlFeMnSi phases with varying Mn/Fe atomic ratios: Experimental studies and DFT calculations

Investigation of the Thermal Deformation Behavior Exhibited by Oxidation Products in Fe–Si Alloys

Enhancing oxidation resistance with Si in Fe36Ni36Al15Cr10Si2Mo1 multi-principal element alloy at 700 °C

Exploring crystal structures, stability and mechanical properties of Fe, Mn-containing intermetallics in Al-Si Alloy by experiments and first-principles calculations

Effect of Si content on interfacial reaction and properties between solid steel and liquid aluminum

The Effect of Niobium on the Changing Behavior of Non-Metallic Inclusions in Solid Alloys Deoxidized with Mn and Si during Heat Treatment at 1473 K

Effect of Si on Fe-rich intermetallic formation and mechanical properties of heattreated Al-Cu-Mn-Fe alloys

High‐Temperature Oxidation of Fe–Si Alloys in Atmospheres Containing 2.0% SO2 + 5.0% O2

Solid reactions between CaO–Al2O3 and Si–Ti-containing steel at 1273 K

Strong elemental interaction enhances the thermal stability of coherent precipitation strengthened Cu–Ni–Al alloys

The oxidation behavior and interfacial reaction between SiO 2 coating and Ti45Al8.5Nb alloy

Influence of Al2O3 Content and Cooling Rate on Crystallization in Fe2O3–CaO–SiO2–Al2O3 Systems

Effect of SiO2 on Crystallization of Calcium Ferrites in Fe2O3–CaO–SiO2–Al2O3 System in Cooling Process