Abstract:Abstract To meet the requirements of automatic production, a new type of green BAl88Si cored solder was developed. The lap brazing experiments were carried out with copper and aluminum as brazing substrates. The microstructure, phase composition, and corrosion behavior of solder joint interface were studied by field emission scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, electron backscattering diffraction, tensile testing machine, and electrochemical workstation. The results show that the brazing joint of Cu/BAl88Si/Al is metallurgical bonding, and the brazing joint of Cu/BAl88Si/Al is composed of Cu 9 Al 4 , CuAl 2 , a-Al, (CuAl 2 + a-Al + Si) ternary eutectic. In addition, there is no obvious preference for each grain in the brazing joint, and there are S texture {123} , Copper texture {112} , and Brass texture {110} . The interface of Cu 9 Al 4 /CuAl 2 is a non-coherent crystal plane and does not have good lattice matching. The average particle size of CuAl 2 is 11.95 μm and that of Al is 28.3 μm. However, the kernel average misorientation (KAM) value at the brazed joint interface is obviously higher than that at the brazed joint interface copper, so the defect density at the brazed joint interface aluminum is higher than that at the brazed joint interface copper. At the same time, due to poor corrosion resistance at the interface on the aluminum side of the brazed joint, serious corrosion spots and corrosion cracks occur at the same time, which leads to the shear performance of the brazed joint decreasing by about 75% after salt spray test for 240 h.

Development of Low Silver AgCuZnSn Filler Metal for Cu/Steel Dissimilar Metal Joining

Influence of Ni Addition on Corrosion Performance of Medium-temperature Filler Metal with Low Cu Content for Al Brazed Joints

Microstructure and mechanical properties of brazing joint of silver-based composite filler metal

Influence of microalloying with B on the microstructure and properties of brazed joints with Ag–Cu–Zn–Sn filler metal

Microstructure evolution and mechanical properties of Sn-3.5Ag-1.0Zn/Cu joint

Microstructure And Corrosion Behavior Of Si3n4/316l Joints Brazed With Ag-Cu/Ag/Mo/Ag/Ag-Cu-Ti Multilayer Filler

Phase analysis and corrosion behavior of brazing Cu/Al dissimilar metal joint with BAl88Si filler metal

An Impact of Zirconium Doping of Zn-Al Braze on the Aluminum-Stainless Steel Joints Integrity During Aging

Comparative Study on Microstructure and Strength of TiAl/Steel Joints Brazed with Ag-Cu-Ti and Ag-Cu-Zn Filler Metals

Investigation on the microstructure, mechanical and electrical properties of Ti3SiC2/Cu joint obtained by Ti25Zr25Ni25Cu25 amorphous high entropy alloy and Ag composite filler

Investigation of Microstructure and Thermo-stability of Ag-cu-sn Filler Metal Powders Prepared by Mechanical Alloying

Ultrasound-assisted Brazing of Cu/Al Dissimilar Metals Using a Zn–3Al Filler Metal

Microstructure and Mechanical Properties of Al2O3/Cu Joints Brazed with Ag–Cu–Ti+Zn Composite Fillers

Spreading Behavior and Microstructure Characteristics of Dissimilar Metals TIG Welding–brazing of Aluminum Alloy to Stainless Steel

Interfacial features of TiAl alloy/316L stainless steel joint brazed with Zr−Cu−Ni−Al amorphous filler metal

Effect of Filler Wires on Brazing Interface Microstructure and Mechanical Properties of Al/Cu Dissimilar Metals Welding-Brazing Joint

Interfacial microstructure and mechanical properties of joints between ZrO 2 ceramic and 316 stainless steel brazed using Ag–Cu–In–Ti filler

Interfacial microstructure and mechanical properties of WC–Co/40Cr joints brazed at low–temperature with Ag–Cu–Ti + Sn novel filler

Influence of Filler Metal on Microstructure and Properties of Titanium/copper Weld Joint by GTAW Weldments

Microstructural Evolution and Mechanical Reliability of Transient Liquid Phase Sintered Joint During Thermal Aging

Interfacial Microstructure and Mechanical Properties of Pressureless Sintered SiC Ceramic and Stainless Steel Joints Brazed by AgCu/AgCuTi Alloy