Abstract:Introduction: In the past three decades, additive manufacturing (AM), also known as 3D printing, has emerged as a promising technology, which allows the manufacture of complex parts by adding material layer upon layer. In comparison, with other metal-based AM technologies, gas metal arc welding-based additive manufacturing (GMAW-based AM) presents a high deposition rate and has the potential for producing medium and large metal components. To validate the technological performance of such a manufacturing process, the internal quality of manufactured parts needs to be analyzed, particularly in the cases of manufacturing the parts working in a critical load-bearing condition. Therefore, this paper aims at investigating the internal quality (i.e., and mechanical properties) of components manufactured by the GMAW-based AM technology. Method: A gas metal arc welding robot was used to build a thin-walled component made of mild steel on a low-carbon substrate according to the AM principle. Thereafter, the specimens for observing and mechanical properties were extracted from the built thin-walled component. The of the specimen were observed by an optical microscope; the hardness was measured by a digital tester, and the tensile tests were carried out on a tensile test machine. Results: The results show that the GMAW-based AM-built thin-walled components possess an adequate that varies from the top to the bottom of the built component: structures with primary dendrites in the upper zone; granular structure of with small regions of at grain boundaries in the middle zone, and grains of in the lower zone. The hardness (ranged between 164±3.46 HV to 192±3.81 HV), yield strength (YS offset of 0.2% ranged from 340±2 to 349.67±1.53 ), and ultimate tensile strength (UTS ranged from 429±1 to 477±2 ) of the GMAW-based AM-built components were comparable to those of wrought mild steel. Conclusions: The results obtained in this study demonstrate that the GMAW-based AM-built components possess adequate and good mechanical properties for real applications. This allows us to confirm the feasibility of using a conventional gas metal arc welding robot for additive manufacturing or repairing/re-manufacturing of metal components.

Optimization of Process Parameters to Improve the Effective Area of Deposition in GMAW-Based Additive Manufacturing and Its Mechanical and Microstructural Analysis

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Study of the Mechanism of a Stable Deposited Height During GMAW-Based Additive Manufacturing

Process Optimization, Microstructure and Mechanical Properties of Wire Arc Additive Manufacturing of Aluminum Alloy by Using DP-GMAW Based on Response Surface Method

Research on GMAW Based Non-Supporting Thin-Wall Structure Manufacturing

The Effects of Processing Parameters during the Wire Arc Additive Manufacturing of 308L Stainless Steel on the Formation of a Thin-Walled Structure

Microstructural characteristics and tensile properties of ER70S-6 manufactured by Robotic CMT wire-and-arc additive manufacturing

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

Modelling and optimization of weld bead geometry in robotic gas metal arc-based additive manufacturing using machine learning, finite-element modelling and graph theory and matrix approach

Wire Arc Additive Manufacturing of ER-4043 Aluminum Alloy: Effect of Tool Speed on Microstructure, Mechanical Properties and Parameter Optimization

Performance optimization and investigation of metal-cored filler wires for high-strength steel during gas metal arc welding

Multi-objective Optimization of Short-Circuit Gas Metal Arc Welding for Overhang Structures by Grey Relational Analysis Integrated Taguchi Method

Influence of Auxiliary Process on Microstructure and Mechanical Properties of Wire Arc Additive Manufacturing of Thick Wall Depositions

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Selection of Parameters for Optimized WAAM Structures for Civil Engineering Applications

Wire arc additive manufacturing of ER-4043 aluminum alloy: evaluation of bead profile, microstructure, and wear behavior

Influence of metal transfer behavior under Ar and CO2 shielding gases on geometry and surface roughness of single and multilayer structures in GMAW-based wire arc additive manufacturing of mild steel

Effect of welding parameters on microstructure and mechanical properties of mild steel components produced by WAAM

Analysis of Favorable Process Conditions for the Manufacturing of Thin-Wall Pieces of Mild Steel Obtained by Wire and Arc Additive Manufacturing (WAAM)

A preliminary study on gas metal arc welding-based additive manufacturing of metal parts