Abstract:The tribological behavior of the rheoformed and thixoformed nano-sized SiCp/7075 composite parts is investigated. The semisolid stirring temperature has a little influence on the friction coefficient and wear resistance of the rheoformed composite parts. As for the thixoformed composite parts, the average value of the steady-state coefficient of friction increases firstly and then decreases with increasing reheating temperature. Higher wear resistance is achieved at a reheating temperature of 580 degrees C. The average value of the steady-state friction coefficient of the rheoformed composite parts varies from 0.37 to 0.45 upon applied loads of from 20 to 50 N. Weight loss increases slightly upon an increase of applied load from 20 to 40 N. An applied load of 50 N leads to a significant increase of the weight loss. The wear rate decreases firstly and then increases with increasing applied load. As for the thixoformed composite part, the average value of the steady-state friction coefficient and the weight loss decreased with an increasing applied load. However, the wear rate decreases firstly with increasing applied load and then increases. As for the rheoformed composite part, the average value of the steady-state friction coefficient decreases firstly and then increases a little with increasing sliding velocity. Weight loss and wear rate show a first increase and a followed decrease with increasing sliding velocity. As for the thixoformed composite part, the average value of the steady-state friction coefficient shows a decrease with increasing sliding velocity. Weight loss and wear rate exhibit, at first, an increase, and then a decrease with increasing sliding velocity. The average friction coefficient varies from 0.4 to 0.44 with increasing volume fraction of SiC. Weight loss and wear rate decrease with increasing volume fraction of SiC. An increase in dislocation density around the nano-sized SiC particles and the mismatch of the coefficient of thermal expansion (CTE) between 7075 matrix and nano-sized SiC particles during solidification improve the wear resistance of the composite. The dominant wear mechanisms of the rheoformed and thixoformed composite parts are adhesive wear, abrasive wear and delamination wear.

Microstructural Evolution and Wear Behavior of SiCp/7085 Composites Manufactured by Ultrasonic Stirring Casting

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Effect of Heat Treatment on Tribological Properties of SiCp/Al–Mg–Mn–Cu Aluminum Matrix Composites

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Effects of SiC Particle Pretreatment and Stirring Parameters on the Microstructure and Mechanical Properties of SiCp/Al–6.8Mg Composites Fabricated by Semi-Solid Stirring Technique

Microscopic impacts of ultrasonic vibration on interfacial strength of SiCp/Al composites

Tribological Behavior of Nano-Sized SiCp/7075 Composite Parts Formed by Semisolid Processing

Mechanical and Tribological Properties of SiC Whisker‐reinforced SiC Composites Via Oscillatory Pressure Sintering

Influence of micron and nano SiC<sub>p</sub> on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Microstructure and Mechanical Properties of Sicp/Mg-Zn-Ca Composites Fabricated by Stir Casting

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Microstructure and Mechanical Properties of 45 vol.% SiC p /7075Al Composite

Study on friction and wear behavior of SiCp/AZ91D nanocomposites

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

Material deformation and removal mechanism of SiCp/Al composites in ultrasonic vibration assisted scratch test

Different Tribological Behaviors of SiCp/AZ91 Composites Induced by Tailoring the Distribution of SiC Particles

Microstructure and Wear Resistance of Cu-Tic Composites Fabricated by Mechanical Alloying and Spark Plasma Sintering

Preparation and Friction Properties of SiC-Al2O3/2A50 Co-Continuous Composites

Mechanical and tribological properties of SiC whiskers reinforced SiC composites via oscillatory pressure sintering

Influence of micron and nano SiCp on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Microstructures, Interface Structure and Room Temperature Tensile Properties of Magnesium Materials Reinforced by High Content Submicron SiCp