Abstract:Laser powder bed fusion (LPBF) is a typical additive manufacturing technology that offers significant advantages in the production of complex components. With the rapid heating and cooling characteristics of LPBF, a large amount of solid solution of alloying elements in the matrix can be achieved to form supersaturated solid solutions, thus enhancing the properties of LPBF alloys. For the unique microstructure, the heat treatment process needs to be adjusted accordingly. In this work, a Zr/Sc-modified Al-Mg alloy processed by laser powder bed fusion (LPBF) with relatively low cost and good mechanical properties was investigated. The fine microstructure was obtained under rapid solidification conditions. The nanoscale Al3(Sc,Zr) particles precipitated at the molten pool boundary during solidification. These particles, as effective heterogeneous nucleators, further refined the α-Al grains and improved the mechanical properties of the alloy. As a result, the alloy exhibited a heterogeneous microstructure consisting of columnar grains in the center of the molten pool and equiaxed grains at the boundaries. The rapid solidification resulted in the supersaturation of solute atoms in the α-Al matrix, which significantly enhanced the solid solution strengthening effect. With the LPBF processing parameters of a combination of a laser power of 250 W, a laser scanning speed of 833 mm/s, and stripe scanning mode, the tensile strength of the alloy reached 401.4 ± 5.7 MPa, which was significantly higher than that of the cast alloys with aging treatment (281.1 ± 1.3 MPa). The heat treatment promoted the formation of secondary Al3(Sc,Zr), Mn/Mg-rich phases. The ultimate tensile strength and elongation at fracture after aging at 325 °C for 2 h were 536.0 ± 1.7 MPa and 14.8 ± 0.8%, respectively. The results provide insight into the preparation of aluminum alloys with relatively low cost and excellent mechanical properties.

The Evolution of Microstructure, Mechanical Properties and Fracture Behavior with Increasing Lanthanum Content in AZ91 Alloy

Effect of La on microstructure and properties of AZ61 magnesium alloy

Microstructure and mechanical properties of Mg–Al based alloy with calcium and rare earth additions

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Effect of Lanthanum Addition on Grain Refinement and Mechanical Properties of Mg–9Li–3Al Alloy

EFFECT OF CERIUM AND LANTHANUM ALLOYING ON MICROSTRUCTURE AND CORROSION BEHAVIOR OF AZ91 MAGNESIUM ALLOY

Effect of minor lanthanum on the microstructures, tensile and electrical properties of Al-Fe alloys

Effect of La/Nd ratio on microstructure and tensile properties of AZ91-RE alloys

Balancing strength and ductility of LA141 alloy with a micro-nano laminated structure

Effect of La Addition on Microstructure, Mechanical Behavior, Strengthening and Toughening Mechanisms of Cast Mg-Gd-Zn Alloy

Microstructure, tensile properties and fracture behaviour of an Al-Cu-Li-Mg-Zr alloy 8090

Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF

Effects of La addition on the mechanical properties and thermal-resistant properties of Al–Mg–Si–Zr alloys based on AA 6201

Comparative study of corrosion behaviors of die cast LA42 and AZ91 alloys

Microstructure and Properties of Az91d Alloy with Ca Additions

Behavior and Mechanisms of Deformation in Intermetallic Compound Al66Mn 9Ti25+la

Microstructural evolution, precipitation behavior and mechanical properties of a novel Al–Zn–Mg–Cu–Li–Sc–Zr alloy

Selective laser melted AZ91D magnesium alloy with superior balance of strength and ductility

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Microstructure, mechanical properties and fracture behaviors of large-scale sand-cast Mg-3Y-2Gd-1Nd-0.4Zr alloy