Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Effect of Tungsten on the Microstructure Evolution and Mechanical Properties of Yttrium Modified HP40Nb Alloy

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

Influence of Tungsten on Microstructure and Properties of As-Cast Hi-Cr Cast Iron

Effect of Tungsten Addition on Continuous Cooling Transformation and Precipitation Behavior of a High Titanium Microalloyed Steel

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Effect of heat treatment and thermomechanical processing on microstructure and tensile property of Ti-44Al-8Nb-0.2W-0.2B-0.5Y alloy

Precipitation control by W addition in aged heat-resistant austenitic 22Cr-25Ni steels and its effect on mechanical properties

Effect of tungsten micro-scale dispersed particles on the microstructure and mechanical properties of Ti–6Al–4V alloy

Microstructure Evolution of Ti–46Al–6Nb–（Si,B） Alloys During Heat Treatment with W Addition

Microstructural stability, phase evolution and mechanical properties of a forged W-modified high-Mn β-γ-TiAl alloy

The effect of Ti–Mo–Nb on the microstructures and tensile properties of a Fe–Mn–Al–C austenitic steel

Effects of Cr Content on Microstructure and Mechanical Properties of WMoNbTiCr High-Entropy Alloys

Effect of heat treatment on microstructures and properties of Y bearing tial alloy

Mechanical Properties and Microstructures of W–TiC and W–Y2O3 Alloys Fabricated by Hot-Pressing Sintering

Effect of rare earth y on microstructures and mechanical properties of Ti-45Al-5Nb alloy

Research on Microstructure, Mechanical Properties, and High-Temperature Stability of Hot-Rolled Tungsten Hafnium Alloy

Avoiding microstructural instabilities in high tungsten containing superalloys by adjusting Al content

Microstructure and mechanical properties of high density tungsten alloy and its influence factors

Effect of tantalum addition method on microstructure and mechanical properties of the 90(W 20Ta)–Ni–Fe alloy

Investigation on the Microstructural Evolution and Precipitation Hardening Mechanism of 1cr15ni36w3ti Superalloy with Varied C Contents

Effects of Cr and W in TiMoNb Refractory High Entropy Alloys