Abstract:This experiment examined the residual stresses on electrodeposited NiCo-Al and NiCo-Zr composite coatings as well as the impact of varying Co(2+)concentrations on other properties of the coating, namely grain size and texture. To prepare for the experiments, this project employed modified Watt Baths containing NiSO4 center dot 6H(2)O (240 g/L), NiCl2 center dot 6H(2)O (40 g/L), H3BO3 (30 g/L) and C12H25NaSO4 (0.2 g/L) in order to electrically deposit them on to Aluminum and Zirconium and to produce the two types of aforementioned specimen: NiCo-Al and NiCO-Zr. The amount of Co in the end product is regulated via adjusting the concentration of CoSO4 center dot 7H(2)O, providing a range of concentrations from 5 to 40 g/L. Furthermore, structural analyses of the coatings were performed via X-ray diffraction at 40kV and 30mA in standard 2 theta-theta mode. The Voigt method was used to calculate grain size and micro-strain of coatings using the integral breadth of the (200) peak. Residual stresses on the as-deposited composite coatings were measured by using stress analyzer and classical sin2 psi method. Peaks of (331)alpha of Ni were selected to calculate the residual stresses. Results show that, for both NiCo-Al and NiCo-Zr composite coatings, grain size decreases and micro-strain increases with increasing Co contents. Pole figure experiments shown typical fiber texture for composite coatings. Texture coefficient results show that the (111) texture coefficient increases while (111) texture coefficient decreases with increasing Co content. In addition, results show that the residual stress of NiCo-Al and NiCo-Zr composite coatings increases as Co content increases, which could be attributed to decreasing grain size and texture evolution from (200) texture to (111) texture.

Residual Stresses on Electro-Deposited Nico-Al and Nico-Zr Composite Coatings

Effect of Electrodeposition Parameters on the Evolution of Crystallographic Texture and Internal Stress of Ni/ZrC Composite Coatings

Effects of Co Contents on the Microstructures and Properties of Electrodeposited NiCo–Al Composite Coatings

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Fabrication and Characterization of Ni–Zr Composite Coatings Using Electrodepositing Technique

Electrodeposition and Mechanical Property of Ni–Co–ZrC Coatings

Microstructure and Texture of Electrodeposited Ni–ZrC Composite Coatings Investigated by Rietveld XRD Line Profile Analysis

Two Stages for the Evolution of Crystallite Size and Texture of Electrodeposited Ni–ZrC Composite Coating

Electrodeposition of Ni Matrix Composite Coatings Containing Zrc Particles

Analysis on the Residual Stresses in Functionally Gradient ZrO_2/NiCoCrAlY Coatings

Microstructure and Corrosion Behavior of Electrodeposited Ni-Co-ZrC Coatings

Effect of Particle Concentration on Property of Electrodeposited Ni–ZrC Nanocomposites

Characterisation of Electrodeposited Ni–Zr Coatings Prepared at Different Current Densities

Influences of Al and Ti particles on microstructure, internal stress and property of Ni composite coatings

Microstructure evolution and improved corrosion resistance of electrodeposited NiCo-Al composite coatings with different Al contents

Effects of compositional gradient and thickness of coating on the residual stresses within the graded coating

Annealing Behaviour of Electrodeposited Ni–Zr and Ni–Al Composite Coatings

Effect of Surface Roughness and Structure Features on Tribological Properties of Electrodeposited Nanocrystalline Ni and Ni/Al2O3 Coatings

Investigation on the evolution of microstructure and texture of electroplated Ni–Ti composite coating by Rietveld method

Tailoring role of Al and Ti particles in the microstructure and property of electrodeposited Ni matrix nanocomposite coatings

Enhanced mechanical properties and corrosion resistance of electro-deposited NiCoP composite coatings with ZrB2 particle addition