Abstract:The nickel-based Inconel 718 alloy, known for its high strength, hardness, and temperature resistance, is widely used in cutting-edge industries such as aerospace. However, after wire electrical discharge machining (WEDM), the alloy surface can experience varying degrees of thermal damage, leading to a significant deterioration in the service performance of manufactured parts. In this study, single-factor experiments were conducted on the nickel-based Inconel 718 alloy to investigate the effects of different machining parameters on the surface quality, material removal rate, and microstructure. Using Taguchi experiments, parameter combinations that achieved the maximum material removal rate and minimum surface roughness were obtained. Based on parameter optimization, multiple trimming strategies were employed to study the effects of multiple trimming on the evolution of the surface microstructure and mechanical properties of Inconel 718 alloy parts. The results showed that with an increase in the number of trimmings, the thermal damage to the surface gradually decreased. After multiple trimmings, the roughness average (Ra) value was reduced to 0.396 μm, the recast layer thickness was reduced from 9.035 μm to 0.92 μm, and the surface hardness approached that of the substrate, effectively removing the surface-hardened layer. The tensile strength of the samples after multiple trimmings increased by 52.2 MPa. The fracture strain of the main cutting was 63.1%, while that after multiple trimmings was approximately 67%. The stress required to fracture the sample increased, thereby enhancing the mechanical properties. The thickness of the brittle fracture zone at the fracture edge was reduced from 18.89 μm to 6.65 μm. The findings indicate that parameter optimization and multiple trimming strategies can improve the surface quality and mechanical properties of Inconel 718 alloy workpieces.

Effects of Overlap Rate and Energy Density on Mechanical Properties of Inconel 718 by Multiple Small-Spot-lsp Impacts

Laser shock peening as a post-processing technique for Inconel 718 components manufactured by laser powder bed fusion

Impact on Mechanical Properties and Microstructural Response of Nickel-Based Superalloy GH4169 Subjected to Warm Laser Shock Peening

Inconel 718 produced by laser powder bed fusion: an overview of the influence of processing parameters on microstructural and mechanical properties

Study on chip formation and surface integrity of nickel-based superalloy Inconel 718 by laser assisted micro-cutting

Improving surface quality and superficial microstructure of LDED Inconel 718 superalloy processed by hybrid laser polishing

Effect of processing parameters on surface roughness, porosity and cracking of as-built IN738LC parts fabricated by laser powder bed fusion

Ultrasonic Vibration-Assisted Laser Engineered Net Shaping of Inconel 718 Parts: Microstructural and Mechanical Characterization

High-throughput investigation of laser powder bed fabricated Inconel 718 alloy: Fabrication, microstructure and performance

Effect of Ultrasonic Shot Peening and Laser Shock Peening on the Microstructure and Microhardness of IN738LC Alloys

Effects of Multiple Laser Shock Peening Impacts on Microstructure and Wear Performance of Wire-Based Laser Directed Energy Deposition 17-4PH Stainless Steel

Study on the Effect of Powder-Bed Fusion Process Parameters on the Quality of as-Built IN718 Parts Using Response Surface Methodology

Mapping of 5-HT-moduline binding sites in guinea-pig brain by film and digital autoradiography

Influence of Deposition Parameters on Hardness Properties of InconelTM 718 Processed by Laser Powder Bed Fusion for Space Applications

Surface Microstructure Evolution and Mechanical Property Investigation of Inconel 718 Alloy Using Multiple Trimmings and WEDM

Laser shock peening induced mechanical properties enhancement of 50CrVA alloy

Grinding- and robotic hammer peening-induced modifications in the near-surface regions of laser-cladded Inconel 718 coatings

Effects of heat treatment on surface integrity and wear performance of Inconel 718 alloy fabricated by laser powder bed fusion process additive manufacturing under different laser power and scanning speed parameters

Experimental investigation of process parameter variations on the microstructure and failure behavior of IN718 structures in PBF-LB/M

Effect of Laser Energy Density on the Microstructure and Microhardness of Inconel 718 Alloy Fabricated by Selective Laser Melting

Effect of heat treatment on microstructures and mechanical properties of Inconel 718 additively manufactured using gradient laser power