Abstract:The effects of Ce and In on microstructure and corrosion properties of Zn-9Al-2.5Mg had been investigated in this research. The corrosion product morphology and the corrosion mechanism were observed and discussed. The microstructure and the corrosion product morphology were seen by OEM and SEM respectively. The phases were determined by XRD and the elements in micro region were used by EDS. The corrosion behavior was determined by full immersion corrosion method and electrochemical test method. Results show that the phases of Zn-9Al-2.5Mg alloy are constituted by Zn-rich solid solution, Al-rich solid solution and ternary eutectic structure (Zn-Al-MgZn2/Mg2Zn11). After adding 0.1% Ce, the grain size of the Zn-9Al-2.5Mg alloy is obviously refined. After adding 0.1% Ce and 0.05% In, the amount of Al-rich solid solution is inhibited and dendriticZn-rich solid solution increased. The amount of ternary eutectic structure (Zn-Al-MgZn2/Mg2Zn11) decreases gradually. Compared with Zn-9Al-2.5Mg alloy, the corrosion potential of Zn-9Al-2.5Mg-0.1Ce increased slightly and the corrosion current density is basically unchanged, which remains at 5.97 x 10(-6) A cm(-2). It's half the corrosion rate of pure Zn. When the content of In increases from 0.05% to 0.1%, the current density increases from 8.71 x 10(-6) A cm(-2) to 20.42 x 10(-6) A cm(-2). The corrosion products of pure Zn and Zn-9Al-2.5Mg alloys are Zn-5(OH)(6)(CO3) (2) and Zn-5(OH)(8)Cl.H2O, Which present sphere (petal and rod) assembly structure. The difference is that the formation of Zn-Al andMg-Al layered double hydroxides (Zn4Al2(OH)(12)CO3 center dot 3H(2)O and Mg6Al2 (OH)(16)CO3 center dot 4H(2)O)-LDH are observed for Zn-9Al-2.5Mg alloys. After adding Ce to Zn-9Al-2.5Mg alloy, the LDH filmis rather compact. But the LDH film is thin and floccus after In added. It leads to a lower resistance of corrosion products and accelerate the corrosion process.

Effects of Ce and In on microstructure and corrosion properties of Zn-9Al-2.5Mg alloy

Effect of Ce on the Microstructure and Corrosion Resistance of Al-5Mg-3Zn-1Cu Alloy

Effect of Zn Concentration on Microstructure and Corrosion Resistance of Mg-Zn Alloys Microalloyed with Ca and Ce

Effect of Cerium on Microstructure, Mechanical Properties and Corrosion Properties of Al-Zn-Mg Alloy

Effects of Ce on Microstructure and Corrosion Resistance of Mg-9Gd-4Y-1Nd-0.6Zr Alloy

Corrosion behavior of lithium silicate-based Zn-5.5Al-4.5Mg-0.3Ce coating

Effects of Ce on Corrosion Behavior of As-cast Mg-Li-Al-Ca Alloy in NaCl Solution

Enhanced Corrosion Resistance of Mg17Al12 Compounds by Ce Modification

Effects of Cerium on the Microstructure and Mechanical Properties of Mg–20Zn–8Al Alloy

Influence of Microalloying with Ca and Ce on the Corrosion Behavior of Extruded Mg-3Al-1Zn

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

Effects of Ce on Microstructure of Semi-Continuously Cast Mg-1.5Zn-0.2Zr Magnesium Alloy Ingots

Effect of Ce on corrosion behaviors of aluminum in 3.5% NaCl solution

Effect of Ce Addition on Microstructure, Mechanical Properties and Corrosion Behavior of Al-Cu-Mn-Mg-Fe Alloy

Effect of Ce on Microstructure, Mechanical Properties and Corrosion Behavior of High-Pressure Die-Cast Mg–4Al-based Alloy

EFFECT OF TRACE CE ON THE MICROSTRUCTURE AND CORROSION RESISTANCE OF AZ91 MAGNESIUM ALLOY

Influence of Al-Mg-Ce on the Anti-Corrosion Performance of the Hot-Dip Coating

Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys

Enhanced Mechanical Properties and Corrosion Resistance of Rolled Mg-1.5Sn-0.5Ca Alloy by Ce Microalloying

Influence of cerium on microstructures and mechanical properties of Al-Zn-Mg-Cu alloys

Effects of Ce Addition on Microstructure, Mechanical Properties and Corrosion Resistance of As-Cast Az80 Magnesium Alloy