Abstract:Forming magnesium alloys with rare earth elements (La, Gd, Nd, Y, Ce) is a routine method for modifying their microstructure and properties. In the present work, the effect of Ce addition on the microstructure evolution and the mechanical properties of as-extruded Mg-8Al-0.5Zn (AZ80) alloy was investigated. All of the extruded AZ80-xCe (x = 0, 0.2, 0.8 and 1.4 wt %) alloys exhibited equiaxed grains formed by fully dynamic recrystallization, and the grain size of the extruded AZ80 alloy was remarkably reduced by ~56.7% with the addition of 1.4 wt % Ce. Furthermore, the bulk-shaped Al4Ce phase formed when Ce was first added, with the Ce content rising to 0.8 wt % or higher, and Al4Ce particles in both the nano- and micron sizees were well distributed in the primary α-Mg matrix. The area fraction of the Al4Ce particles expanded with increasing Ce content, providing more nuclei for dynamic recrystallization, which could contribute to the grain refinement. The results of the tensile tests in this study showed that Ce addition effectively improved the room temperature formability of the as-extruded AZ80 alloy, without sacrificing strength. The significantly improved mechanical properties were ascribed to excellent grain refinement, weakened texture strength, an increased Schmid factor, and a reduced area fraction of low-angle grain boundaries, all resulting from Ce addition to the as-extruded AZ80 alloy. The contribution of the nano-Al4Ce precipitates on improving the mechanical properties was also discussed in this paper.

Effect of Ce content and rolling route on the microstructure and mechanical properties of high-Zn content Al-Zn-Ce alloys

Effect of Ce Content on the Microstructure and Mechanical Properties of Al-Cu-Li Alloy

Effect of Ce on microstructure and dynamic compression properties of ZK60 alloy

Effect of cerium alloying on microstructure, texture and mechanical properties of magnesium during cold-rolling process

Effect of Ce Addition on Modifying the Microstructure and Achieving a High Elongation with a Relatively High Strength of As-Extruded AZ80 Magnesium Alloy

Microstructure and Mechanical Properties of As-Cast Al-10Ce-3Mg-xZn Alloys

Enhanced Mechanical Properties and Corrosion Resistance of Rolled Mg-1.5Sn-0.5Ca Alloy by Ce Microalloying

Influence of Ce content on the microstructures and tensile properties of Mg-1Gd-0.5Zn alloys

Effect of rolling temperature on deformation behavior and mechanical properties of Mg-8Li-1Al-0.6Y-0.6Ce alloy

The effects of Zr content and hot rolling on the microstructure and mechanical properties of Zn-1.5Cu-1.0Ag-xZr alloys

A comparative study on the effect of 0.5 wt% Ca or Ce on the microstructure, texture, and mechanical properties of the hot-rolled Mg-4Li alloy

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Enhanced load transfer and ductility in Al–9Ce alloy through heterogeneous lamellar microstructure design by cold rolling and annealing

Effect of rolling on the structure and mechanical properties of the Zn-0.8Li alloy

Effect of Hot Forging Process Parameters and Ce Addition on the Microstructure and Mechanical Properties of an As‐Forged AZ80 Alloy

Effect of Ce and Y on Microstructures and Properties of Al-11.0Zn-3.1Mg-1.22Cu-0.1Sr-0.2Zr-0.1Ti Alloy

Effect of Ce/La Microalloying on Microstructural Evolution of Mg-Zn-Ca Alloy During Solution Treatment

Effects of rolling processing on the microstructures, mechanical properties and strain softening behavior of biodegradable Zn-0.06 Mg alloy

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Effect of Ce Addition on the Microstructure, Thermal Conductivity and Mechanical Properties of Mg–0.5Mn Alloys