Abstract:The impact of Zn on the mechanical properties and corrosion resistance of Al-Mg-Si alloys with high Cu contents was studied through microstructure analysis and accelerated corrosion testing. The age-hardening response of the alloy improved with the addition of trace Zn, and the poor corrosion resistance caused by high Cu content was overcome. Intergranular corrosion susceptibility (IGC) decreased and then increased with increasing Zn content. Al-Mg-Si-Cu alloys that contain 0.5 wt.% Zn possessed the best corrosion resistance. Zn decreased the potential difference between the matrix and the Al(Mn, Fe)Si phases according to scanning Kelvin probe force microscopy (SKPFM) tests, which reduced the driving force of corrosion in the alloy. Additionally, the addition of Zn promoted discontinuous precipitation at the grain boundaries, which was conducive to enhancing the IGC resistance. However, excessive Zn (1.0 wt.%) promoted the diffusion of more solute atoms near the grain boundaries to the grain boundaries, which coarsened the precipitated phase at the grain boundaries and shortened the interphase distance. Moreover, as the width of the PFZ increased, the concentration of solute atoms decreased, and the potential difference between the precipitated phase and the PFZ increased, leading to more severe IGC behavior. Therefore, an appropriate Zn content was beneficial for improving the corrosion properties and age-hardening response of Al-Mg-Si-Cu alloys.

Effects of Indium on Corrosion Behavior of Mg-Al-Cu Alloy

Effect of Al Addition and Heat Treatment on the Microstructures and Corrosion Resistance of Mg-Cu Alloys

In vitro investigation on microstructure, bio-corrosion properties and cytotoxicity of as-extruded Mg–5Sn–xIn alloys

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Corrosion behavior characterization of as extruded Mg-8Li-3Al alloy with minor alloying elements (Gd, Sn and Cu) by scanning Kelvin probe force microscopy

Effect of In addition on the precipitation behavior and mechanical property for Al-Mg-Si alloys

Influence of β-Mg 17 Al 12 and Al-Mn intermetallic compounds on the corrosion behaviour of cast and solution treated Mg-Al-Zn-Mn alloys

Effect of Trace Zn on the Mechanical Properties and Corrosion Behavior of Al-Mg-Si Alloys with High Cu

Effect of Alloying Mg on Corrosion Resistance of Cu at High Temperature

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Effect of Al Element on the Microstructure and Properties of Cu-Ni-Fe-Mn Alloys

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment

The effect of indium microalloying on lead-free solders: A review

Effects of Al addition on corrosion behavior and mechanical property of high-strength and high-elasticity Cu-20Ni-20Mn-0.3Nb-0.3Cr-0.3Zr alloy

Effect of Mg on the Corrosion Resistance of Hot-Dip Zn-Cu-Ti Alloy

Influences of trace indium and bismuth addition on corrosion behavior of zinc in alkaline solutions

Effect of Intermittent Variable Rate Non-isothermal Aging on the Corrosion Resistance of Al-Zn-Mg-Cu Alloy

Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys

Microstructure, Mechanical Properties, and Corrosion Behavior of Al-4.0Cu-1.1Li-0.5Mg-xAg Alloys

An investigation of the impacts of non-isothermal aging on the microstructures and corrosion of WE43 Mg alloy

Effect of copper content on the corrosion behaviors and antibacterial properties of binary Mg–Cu alloys