Abstract:The AlN/BN composite ceramic, fabricated via hot-press sintering, exhibits obvious anisotropy due to the establishment of directional alignment of h-BN. However, the variation and influence mechanisms of bending strength (σ) and thermal conductivity (λ) are remain unclear in different directions, which greatly limit the application of AlN/BN composite ceramics. In this paper, the effects of h-BN content on phase composition, microstructure and anisotropy of AlN/BN composite ceramics are discussed in detail. The results reveal that AlN/BN composite ceramics have three directions: perpendicular (⊥), longitudinal parallel (∥), and lateral parallel (≡) to the hot-pressing direction. The content of h-BN is a crucial factor affecting the anisotropy of AlN/BN composite ceramics. h-BN enhances the thermal conductivity in the ∥ and hinders the thermal conductivity in the ⊥. With the increase in h-BN amount, λ∥ rises gradually, while λ⊥ gradually falls. When the mass percentage of h-BN and AlN is 25 % (AB25), the λ∥ is as high as 90 W m−1 K−1, which is about 2.25 times that of λ⊥. In terms of mechanical properties, σ ≡ and σ ⊥ first increase and then decrease, while σ ∥ only decreases. This is attributable to h-BN being effective in enhancing mechanical properties by inhibiting crack propagation in the ⊥ and ≡ direction, while the promotion of crack propagation leads to a decrease in mechanical properties in the ∥ direction. σ ≡ reaches the highest values (σ ≡ = 460.2 MPa) at an h-BN amount of 10 % (AB10), which is about 1.19 and 2.04 times that of σ ⊥ and σ ∥, respectively, and 22.1 % higher than that of AB0.

Effects of Aln Content on the Thermal Properties and Thermal Shock Resistance of Bn Matrix Composite Ceramic

Effects of AlN Content on Phase Composition, Microstructure and Mechanical Properties of BN-based Composite Ceramics

Enhanced thermal shock resistance of BN-based composites sintered by hot-pressing with the introduction of nano oxides

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Effects of AlN content on phase composition, microstructure and mechanical properties of DN-based composite ceramics

Effect of aln content on the microstructure and mechanical properties of bn-based composites

Thermal Shock Behaviors of AlN / BN Laminated Ceramic Composites

Microstructure, mechanical properties and thermal shock behavior of h-BN–AlN ceramic composites prepared by combustion synthesis

YAlO3 reinforced AlN composite ceramics with significantly improved mechanical properties and thermal shock resistance

Effect of BN on Sintering Property and Titanium Melt Erosion Resistance of AlN Refractories

Effect of hexagonal boron nitride content on the anisotropy of hot-press-sintered AlN/BN composite ceramics

High-pressure synthesis of Al<sub>2</sub>O<sub>3</sub>-cBN composites: Effect of thermodynamic condition and cBN volume fraction on their microstructure and properties

Mechanical Properties and Thermal Shock Resistance of BaAl2Si2O8/BN Ceramic Composites

Effect of BN content on microstructures, mechanical and dielectric properties of porous BN/Si3N4 composite ceramics prepared by gel casting

Thermal properties and thermal shock resistance of BAS-BN composite ceramics

Thermal Shock Resistance Behavior of Machinable Al2O3/BN Nanocomposites

Improvement in mechanical properties in AlN-h-BN composites with high thermal conductivity

Microstructural Evolution and Mechanical Properties of H-Bn Composite Ceramics with Y 2 O 3 –aln Addition by Liquid-Phase Sintering

Preparation and properties of sintering additive-free AlN–BN composite ceramics by hot-pressing sintering

Effect of Boron Nitride Content on Mechanical、dielectric and Thermal Shock Resistance Properties of Si3N4-BN-MAS Composites

Effect of AlN content on the properties and microstructure of pressureless-sintered Al 2 O 3-AlN composites