Abstract:Due to the low transport resistance, mullite hollow fiber (HF) could be regarded as a promising support for preparation of NaA zeolite membranes. However, insufficient coverage and undesired seed penetration often occur in the seeding step of the mullite support due to the rough surfaces with ultra-large macropores (2-4 μm). This leads to poor intergrowth of the membrane layer. To solve this issue, cationic polyacrylamide (CPAM) was employed to modify the chemical and electrostatic properties of the mullite HF surface, where the electrostatic attraction between the surface and seed crystals could significantly promote the coating effect. In the seeding, the original seeds (3.2 μm) were mixed with the ball-milled seeds (0.3 μm) to improve the seed coverage, i.e., the original seed was used to block the macropores on the support surface to prevent the penetration of small seeds, while the decked ball-milled seed was used to provide sufficient active sites to induce the intergrowth of the zeolite crystals. The effects of the concentration of CPAM, mixed mass ratio of seeds, and seed concentration on the preparation of NaA zeolite membranes were systematically examined, where the separation performances were characterized by pervaporation (PV) dehydration of 90 %(mass) ethanol/water mixtures at 75 °C. The results indicated that under a CPAM concentration of 0.7 %(mass), an equivalent mass ratio of mixed seeds in a seed concentration of 1.0 %(mass), the prepared mullite HF supported NaA zeolite membrane yielded the best PV performance, where the permeation flux and separation factor corresponded to 5.45 kg·m −2 ·h −1 and 10000, respectively, being sufficient for industrial applications. Graphical abstract Download: Download high-res image (212KB) Download: Download full-size image

Preparation and Characterization of NaA Zeolite Membranes on Inner-surface of Four-channel Ceramic Hollow Fibers

The preparation of zeolite NaA membranes on the inner surface of hollow fiber supports

Preparation of high-performance zeolite NaA membranes in clear solution by adding SiO2 into Al2O3 hollow-fiber precursor

High performance zeolite NaA membranes synthesized on the inner surface of zeolite/PES–PI blend composite hollow fibers

Preparation of Asymmetric Zeolite NaA Membrane Layers by Vapor Phase Transfer and Seeded Growth Method

Preparation of zeolite MFI membranes on alumina hollow fibers with high flux for pervaporation

A Facile Preparation of High Flux NaA Zeolite Membranes by Direct Secondary Growth of Wet Gel Layer

Manipulation of the Surface Microstructure and Its Effects on the Flux of NaA Zeolite Membranes in Pervaporation

Silane-modified NaA/PAAs hybrid membranes for ethanol dehydration by pervaporation

Ultrasonic Treatment of Polyacrylic Acid Sodium/Naa Zeolite Hybrid Membranes for the Pervaporation Dehydration of Ethanol

Preparation of Zeolite NaA Membranes on Macroporous Alumina Supports by Secondary Growth of Gel Layers

CPAM-assisted synthesis of NaA zeolite membrane on macroporous mullite hollow fiber for ethanol dehydration by pervaporation

High Performance Zeolite Lta Pervaporation Membranes on Ceramic Hollow Fibers by Dipcoating-Wiping Seed Deposition

Microstructure Manipulation of MFI-type Zeolite Membranes on Hollow Fibers for Ethanol–water Separation

Silane-Modified Naa Zeolite/Paas Hybrid Pervaporation Membranes for the Dehydration of Ethanol

Fabrication of Zeolite Naa Membranes on Hollow Fibers Using Nano-Sized Seeds Exfoliated from Mesoporous Zeolite Crystals

Influences of adding organic intermediate layer on membrane formation and properties

Heat treatment for improving performance of inner-side zeolite NaA membranes on composite hollow fibers

Zeolite NaA membranes supported on alumina hollow fibers: Effect of support resistances on pervaporation performance

Zeolite membranes on hollow fiber supports

The influence of nanoseeds on the pervaporation performance of MFI-type zeolite membranes on hollow fibers