Abstract:NaA/polymer composite hollow fibers (CHF) used as zeolite NaA membrane supports are fabricated from the dope slurry of NaA zeolite, N-methyl-2-pyrrolidone (NMP) and polyethersulfone (PES) using a dry–wet spinning process. The CHF supports can avoid seeding process and have great potential for developing low-cost zeolite membranes with high reproducibility. The influences of the spinning condition, the zeolite loading and particle size on the properties of the CHF supports and zeolite NaA membranes are investigated in detail. The supports and membranes were characterized by SEM, bending strength tests and water/ethanol pervaporation separation tests. Dense membranes with the separation factor >10,000 were obtained on the Z1 (4.0μm)-85 (85wt.% NaA) and Z2 (1.5μm)-75 supports after the synthesis of 5h, while the zeolite membranes obtained on the Z1-70 and Z1-75 supports had pinholes. A dense membrane with the separation factor >10,000 was obtained on the Z2-85 support after the synthesis of 4h. The results indicate that the CHF supports with smaller zeolite particles were better as the supports for zeolite NaA membranes. The flux of the zeolite membrane on the CHF support increased with the zeolite loading because the increase of the zeolite loading resulted in the increase of the support porosity. However, the increase of the zeolite loading can reduce the mechanical strength of the supports.

Fabrication of Zeolite Naa Membranes on Hollow Fibers Using Nano-Sized Seeds Exfoliated from Mesoporous Zeolite Crystals

Preparation of high-performance zeolite NaA membranes in clear solution by adding SiO2 into Al2O3 hollow-fiber precursor

High-Performance Zeolite Naa Membranes on Polymer-Zeolite Composite Hollow Fiber Supports

Influences of Seeds on the Properties of Zeolite NaA Membranes on Alumina Hollow Fibers

The preparation of zeolite NaA membranes on the inner surface of hollow fiber supports

Influences of the Zeolite Loading and Particle Size in Composite Hollow Fiber Supports on Properties of Zeolite Naa Membranes

Manipulation of the Surface Microstructure and Its Effects on the Flux of NaA Zeolite Membranes in Pervaporation

Preparation of Zeolite NaA Membranes on Macroporous Alumina Supports by Secondary Growth of Gel Layers

Induction of Zeolite Membrane Formation by Implanting Zeolite Crystals into the Precursor of Ceramic Supports

High performance zeolite NaA membranes synthesized on the inner surface of zeolite/PES–PI blend composite hollow fibers

Preparation of Asymmetric Zeolite NaA Membrane Layers by Vapor Phase Transfer and Seeded Growth Method

Zeolite membranes on hollow fiber supports

Microstructure Manipulation of MFI-type Zeolite Membranes on Hollow Fibers for Ethanol–water Separation

A Facile Preparation of High Flux NaA Zeolite Membranes by Direct Secondary Growth of Wet Gel Layer

Halloysite Nanotube-Based Electrospun Ceramic Nanofibre Mat: a Novel Support for Zeolite Membranes

Preparation of zeolite MFI membranes on alumina hollow fibers with high flux for pervaporation

Ultrasonic-assisted Fabrication of High Flux T-type Zeolite Membranes on Alumina Hollow Fibers

Hierarchical porous structures by using zeolite nanocrystals as building blocks

Preparation of zeolite MFI membranes on defective macroporous alumina supports by a novel wetting–rubbing seeding method: Role of wetting agent

The influence of nanoseeds on the pervaporation performance of MFI-type zeolite membranes on hollow fibers

Fabrication of B-Oriented MFI Zeolite Membranes by a Printing-Transfer Seed Layer Procedure.