Abstract:In spite of the advantages of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathode materials such as high energy density and high capacity, their capacity decay during cycling is still a significant problem, which are mainly due to the internal structural collapse and the surge in interfacial impedance caused by interfacial side reactions. To address these issues, wet chemical methods and annealing treatments were used to create LiV 2 O 4 -coated and V 4+ -doped NCM811 cathode materials. The LiV 2 O 4 coating layer and the doped V 4+ had little effect on the crystal structure of the NCM811, according to X-ray powder diffraction and Rietveld refinement studies. Scanning electron microscopy, energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy data all showed that the LiV 2 O 4 layer was successfully coated on the surface of the spherical particles and some of the V 4+ was successfully introduced into the bulk phase. Thanks to the ion-conducting layer, LiV 2 O 4 , the interfacial impedance was reduced while the Li + diffusion rate was accelerated, and the V 4+ doped into the bulk phase stabilizes the internal structure, significantly increasing the cycling stability and the rate performance of NCM811. In particular, when the coating amount was 0.6 wt%, the initial discharge specific capacity reached 203.5 mAh/g at 2.8–4.3 V at 0.1 C, and the retention rate was 87.6% after 100 cycles, which was 12.1% higher compared to 75.5% of the original sample. And when the rate was raised to 5 C, the original sample's capacity plummeted to only about 100 mAh/g, but the sample with 0.6 wt% of coating was still 140.9 mAh/g. Experiments confirmed that this LiV 2 O 4 coating modification with synergistic V 4+ doping provided an innovative technique for boosting the electrochemical performance of Ni-rich ternary cathode materials.

Enhanced Electrochemical Capability of LiNi1/3Co1/3Mn1/3O2 Cathode Materials Coated with Fluoroborate Glass for Lithium‐Ion Batteries

Enhanced electrochemical performance of Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 cathode material coated with Li + -conductive Li 2 SiO 3 for lithium ion batteries

Multifunctional Li2O-2B2O3 Coating for Enhancing High Voltage Electrochemical Performances and Thermal Stability of Layered Structured LiNi0.5Co0.2Mn0.3O2 Cathode Materials for Lithium Ion Batteries

LiNbO3 coating improves property of LiNi0.5Mn1.5O4 for lithium-ion battery cathode materials

Enhanced High-Voltage Cycling Stability of Ni-rich LiNi0.8Co0.1Mn0.1O2 Cathode Coated with Li2O–2B2O3

LiBF4 Induced Unique Surface Modification Enables Improved Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Cathode

Effect of Nb2O5 Nanocoating on the Thermal Stability and Electrochemical Performance of LiNi0.6Co0.2Mn0.2O2 Cathode Materials for Lithium Ion Batteries

Effect of carbon coating on electrochemical performance of Li 1.048 Mn 0.381 Ni 0.286 Co 0.286 O 2 cathode material for lithium-ion batteries

Enhanced electrochemical properties of Li1·2Ni0·13Co0·13Mn0·54O2 coated with Al2O3 nano-film

Effect of Nb5+ Doping and LiNbO3 Coating on the Structure and Surface of a LiNi0.8Mn0.2O2 Cathode Material for Lithium-Ion Batteries

In situ formed Li5AlO4-coated LiNi0·8Co0·1Mn0·1O2 cathode material assisted by hydrocarbonate with improved electrochemical performance for lithium-ion batteries

Enhanced electrochemical properties and thermal stability of Zr4+ doped Li1.20Mn0.54Ni0.13Co0.13O2 cathode material by a Li ion conductor of Li3PO4 surface coating

Improving rate capacity and cycling performance of lithium-rich high-Mn Li-1.8[Mn0.7Co0.15Ni0.15]O-2.675 cathode materials by Li2SiO3 coating

Superior Stability Secured by a Four-Phase Cathode Electrolyte Interface on a Ni-Rich Cathode for Lithium Ion Batteries

Improving the Electrochemical Performance of LiNi1/3Co1/3Mn1/3O2 Cathode Material by LiF Modification

(Keynote) MnPO4-Coating for Improved Long-Term Performance of Li(Ni0.4Co0.2Mn0.4)O2 in Ionic Liquid-Based Electrolytes

Enhanced electrochemical performance of LiV2O4-coated and V4+-doped LiNi0.8Co0.1Mn0.1O2 cathode for lithium-ion batteries

Enhanced electrochemical performance of LiNi1/3Co1/3Mn1/3O2 cathode material by Al2O3 surface coating derived via NH2-MIL-53(Al) MOF

Surface coating with Li3BO3 protection layer to enhance the electrochemical performance and safety properties of Ni-rich LiNi0.85Co0.05Mn0.10O2 cathode material

Protective and ion conductive: High-Rate Ni-Rich cathode with enhanced cyclic stability via One-Step bifunctional dual-layer coating

Integrated co-modification of PO43− polyanion doping and Li2TiO3 coating for Ni-rich layered LiNi0.6Co0.2Mn0.2O2 cathode material of Lithium-Ion batteries