Abstract:In spite of the advantages of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathode materials such as high energy density and high capacity, their capacity decay during cycling is still a significant problem, which are mainly due to the internal structural collapse and the surge in interfacial impedance caused by interfacial side reactions. To address these issues, wet chemical methods and annealing treatments were used to create LiV 2 O 4 -coated and V 4+ -doped NCM811 cathode materials. The LiV 2 O 4 coating layer and the doped V 4+ had little effect on the crystal structure of the NCM811, according to X-ray powder diffraction and Rietveld refinement studies. Scanning electron microscopy, energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy data all showed that the LiV 2 O 4 layer was successfully coated on the surface of the spherical particles and some of the V 4+ was successfully introduced into the bulk phase. Thanks to the ion-conducting layer, LiV 2 O 4 , the interfacial impedance was reduced while the Li + diffusion rate was accelerated, and the V 4+ doped into the bulk phase stabilizes the internal structure, significantly increasing the cycling stability and the rate performance of NCM811. In particular, when the coating amount was 0.6 wt%, the initial discharge specific capacity reached 203.5 mAh/g at 2.8–4.3 V at 0.1 C, and the retention rate was 87.6% after 100 cycles, which was 12.1% higher compared to 75.5% of the original sample. And when the rate was raised to 5 C, the original sample's capacity plummeted to only about 100 mAh/g, but the sample with 0.6 wt% of coating was still 140.9 mAh/g. Experiments confirmed that this LiV 2 O 4 coating modification with synergistic V 4+ doping provided an innovative technique for boosting the electrochemical performance of Ni-rich ternary cathode materials.

LiBF4 Induced Unique Surface Modification Enables Improved Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Cathode

Surface Coating of NCM-811 Cathode Materials with G-C3n4 for Enhanced Electrochemical Performance.

In-situ Formation of Hybrid Li3PO4-AlPO4-Al(PO3)3 Coating Layer on LiNi0.8Co0.1Mn0.1O2 Cathode with Enhanced Electrochemical Properties for Lithium-Ion Battery

Facile Surface Coatings for Performance Improvement of NMC811 Battery Cathode Material

Enhanced interfacial reaction interface stability of Ni-rich cathode materials by fabricating dual-modified layer coating for lithium-ion batteries

Multifunctional Integration of Double-Shell Hybrid Nanostructure for Alleviating Surface Degradation of LiNi0.8Co0.1Mn0.1O2 Cathode for Advanced Lithium-Ion Batteries at High Cut-Off Voltage.

Improving the Electrochemical Performance of LiNi1/3Co1/3Mn1/3O2 Cathode Material by LiF Modification

Mixed-conducting Interlayer Boosting the Electrochemical Performance of Ni-rich Layered Oxide Cathode Materials for Lithium Ion Batteries

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

Enhanced electrochemical performance of LiV2O4-coated and V4+-doped LiNi0.8Co0.1Mn0.1O2 cathode for lithium-ion batteries

Synergistic Effect of B-Nb Co-modified to Achieve Crystal Structure and Interface Tuning for Ni-rich Cathode

Uncovering the Role of Nb Modification in Improving the Structure Stability and Electrochemical Performance of LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathode Charged at Higher Voltage of 4.5 V

Superior Stability Secured by a Four-Phase Cathode Electrolyte Interface on a Ni-Rich Cathode for Lithium Ion Batteries

LiNbO3 Coating and F- Doping Stabilize the Crystal Structure and Ameliorate the Interface of LiNi0.88Co0.06Mn0.03Al0.03O2 to Improve the Electrochemical Properties and Safety Capability

Multifunctional Integration of Double-Shell Hybrid Nanostructure for Alleviating Surface Degradation of LiNi<sub>0.8</sub>Co<sub>0.1</sub>Mn<sub>0.1</sub>O<sub>2</sub> Cathode for Advanced Lithium-Ion Batteries at High Cutoff Voltage

Integrated co-modification of PO43− polyanion doping and Li2TiO3 coating for Ni-rich layered LiNi0.6Co0.2Mn0.2O2 cathode material of Lithium-Ion batteries

Stabilization of NCM811 cathode for Li-ion batteries by N-doped carbon coating

Surface-reinforced NCM811 with enhanced electrochemical performance for Li-ion batteries

Protective and ion conductive: High-Rate Ni-Rich cathode with enhanced cyclic stability via One-Step bifunctional dual-layer coating

Sol/Antisolvent Coating for High Initial Coulombic Efficiency and Ultra-stable Mechanical Integrity of Ni-Rich Cathode Materials

Can surface modification be more effective to enhance the electrochemical performance of lithium rich materials?