Abstract:This article presents a novel and feasible approach for researching the quantity of the ceramic phase and component optimization in high-temperature titanium alloys with small trace amounts of ceramic phases. Different near-α titanium alloys with varying yttrium and boron contents were prepared through the utilization of a vacuum non-consumable arc furnace melting method. The alloy used was a Ti-5.9Al-4Sn-3.9Zr-3.8Mo-0.4Si base. Its microstructure, texture, mechanical properties, and fracture behavior were studied. The observation of the as-cast structure shows that the addition of different doses of trace Y and B elements significantly refines both the original β grains and α grains. Moreover, the addition of the B element transforms the Widmanstätten structure in the titanium alloy structure into a basketweave structure. The addition of Y can refine the grain structure, improve the uniformity of the matrix structure, and act as a strong deoxidizer, which will take away the oxygen in the matrix and purify it. The TiB whiskers generated with the addition of B promotes dynamic recrystallization behavior and leads to more equiaxed α grains being precipitated around them, resulting in a significant refinement of the microstructure of the as-cast alloy. After adding a small amount of B, the texture strength of the α phase is significantly reduced, indicating that TiB whiskers inhibit the formation of texture. After conducting performance screening and structure analysis, the study supplements the analysis of Y’s regulation of the titanium alloy structure. The regulation is primarily explained by combining the results of the analysis of boron content, phase diagram analysis, mechanical properties, and fracture analysis. The mechanical analysis introduces the unique load transfer strengthening of TiB whiskers combined with an analysis of high-temperature mechanical properties, as the threshold for addition. The optimal amounts of Y and B additions are 0.6 wt% and 0.8 wt%, respectively. The optimized alloy obtained under this condition can achieve a tensile strength of 950 Mpa at 500 °C without any plastic deformation or heat treatment.

Refining Prior-Β Grains of Ti–6Al–4V Alloy Through Yttrium Addition

Hierarchical Grain Refinement During the Laser Additive Manufacturing of Ti-6Al-4V Alloys by the Addition of Micron-Sized Refractory Particles

Effect of Y on the refinement of cast and rapidly solidified TiAl alloys

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Grain Refinement Effect of ZrB2 in Laser Additive Manufactured Metastable Β-Titanium Alloy with Enhanced Mechanical Properties

Grain and lamellar refinement in TiAl based alloy by yttrium addition

Investigation on the Optimal Amount of Y and B Elements in High-Temperature Titanium Alloy Ti-5.9Al-4Sn-3.9Zr-3.8Mo-0.4Si-xY-yB

Impacts of Yttrium on Microstructure and Tensile Properties of Biomedical Β Ti-Nb-Zr Fabricated by Metal Injection Molding

Effect of Y2O3 addition on microstructure and properties of Ti6Al4V by laser melting deposition

Effects of Minor Yttrium Addition on Microstructure, Mechanical Properties and Hot Workability of Nb or V Containing TiAl Alloys

Effect of Yttrium on Microstructure and Mold Filling Capacity of A Near-Alpha High Temperature Titanium Alloy

Refining Ti 2 AlC in the liquid region and improving the microstructure and mechanical properties of Ti-46Al-8Nb-2.6 C alloy by adding Y

Refining Ti2AlC in the Liquid Region and Improving the Microstructure and Mechanical Properties of Ti-46Al-8 Nb-2.6 C Alloy by Adding Y

Influence of Yttrium on Microstructure, Mechanical Properties and Deformability of Ti–43Al–9V Alloy

Enhanced Strength-Ductility Synergy in Laser Additive Manufactured TC4 Titanium Alloy by Grain Refinement

Grain Refinement by Trace Tib2 Addition in Conventional Cast Tial-Based Alloy

Microstructural evolution in laser melted boron alloyed Ti-6Al-4V

Microstructure and Properties of a Beta-Solidifying TiAl-based Alloy with Different Refiners

Effects of Yttrium on Microstructures and Properties of Ti-17Al-27Nb Alloy

Nano-yttrium-containing precipitates of T6 heat-treated A356.2 alloy when trace yttrium (Y less than 0.100 wt%) added

Optimization of Processing Parameters and Microstructure Evolution of (TiB+La 2 O 3 )/Ti6Al4V Manufactured by Laser Melting Deposition