Abstract:Defect passivation and tailoring of perovskite–charge transport layer interfaces are critical strategies to minimize the recombination losses and improve the power conversion efficiency (PCE) in perovskite solar cells (PSCs). Herein, we use titanium carbide MXene (Ti3C2T x ) to tailor the electronic properties of the electron transport layer (ETL) and ETL/perovskite interface in inverted (p–i–n) PSCs and correlate them to the observed PCE. MXene doping in a [6,6]-phenyl-C61-butyric acid methyl ester (M-PC61BM)-based ETL results in an improved electrical conductivity and ETL/perovskite interface band alignment. A red shift in the Ag(2) peak in the Raman spectrum and a localized upshift of the Fermi level calculated using scanning Kelvin probe force microscopy (SKPFM) confirm the n-doping of PC61BM. Consequently, PSC devices with M-PC61BM as the ETL show a higher PCE of 18% than PC61BM ETL-based control devices (PCE = 15.2%). Importantly, our study proves that the improvement in the open-circuit voltage (V OC) and fill factor (FF) depends on how MXene is integrated into the PSC, i.e., as a dopant in the PC61BM ETL, an interfacial layer between the perovskite and ETL, or a standalone ETL. Through comprehensive photoluminescence, electrochemical impedance spectroscopy, space-charge limited current, and scanning Kelvin probe force microscopy-based analyses, we establish that the introduction of MXene in PSCs has multiple benefits, including improvement in carrier transport, passivation and trap state reduction, and better interfacial energy alignment. Further, we unravel the most prominent factor influencing device performance in each mode of MXene introduction. Hence, the study reinforces the potential of Ti3C2T x MXene as a versatile material for high-performance electronic and optoelectronic devices.

MXene-Modulated Electrode/SnO2 Interface Boosting Charge Transport in Perovskite Solar Cells

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

MXene-Based Tailoring of Carrier Dynamics, Defect Passivation, and Interfacial Band Alignment for Efficient Planar p–i–n Perovskite Solar Cells

Mxene regulates the stress of perovskite and improves interface contact for high-efficiency carbon-based all-inorganic solar cells

Interfacial Engineering of Au@Nb2CTx-MXene Modulates the Growth Strain, Suppresses the Auger Recombination, and Enables an Open-Circuit Voltage of over 1.2 V in Perovskite Solar Cells

Synergistic effect of multifunctional MXene-nanosheet and naphthoquinone sulfonate toward high-performance perovskite solar cells and modules

Rational design of SnO 2 -based electron transport layer in mesoscopic perovskite solar cells: more kinetically favorable than traditional double-layer architecture

Buried Interface Modulation via Preferential Crystallization in All‐Inorganic Perovskite Solar Cells: The Case of Multifunctional Ti3C2Tx

Plasma Oxidized Ti3C2Tx MXene As Electron Transport Layer for Efficient Perovskite Solar Cells

High-Efficiency Perovskite Solar Cells with Improved Interfacial Charge Extraction by Bridging Molecules

Dual Interfacial Modification Engineering with 2D MXene Quantum Dots and Copper Sulphide Nanocrystals Enabled High‐Performance Perovskite Solar Cells

MXene-based novel nanocomposites doped SnO2 for boosting the performance of perovskite solar cells

MXenes as a hole transport interfacial layer for efficient and air-stable quasi-2D perovskite solar cells

MXene-Embedded PEDOT:PSS Hole-Transport Material for Lead-Free Perovskite Solar Cells

Charge transfer enhancement of TiO2/perovskite interface in perovskite solar cells

Enhancing the Efficiency of Perovskite Solar Cells through Interface Engineering with MoS2 Quantum Dots

Anhydrous organic etching derived fluorine-rich terminated MXene nanosheets for efficient and stable perovskite solar cells

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO 2 ‐Based Electron Transport Layers

Substrate Interface Engineering for Drastically Boosted Short-Circuit Current Density and Fill Factor in Perovskite Solar Cells

Hybridization of SnO 2 and an In-Situ-Oxidized Ti 3 C 2 T x MXene Electron Transport Bilayer for High-Performance Planar Perovskite Solar Cells

Enhancement of Electron Transport Characteristics Using MXene-MnFeO3 Nanocomposite Integration with Fullerene Derivatives for the Perovskite-Based Solar Cells and Detectors