Abstract:Organic-inorganic metal halide perovskite solar cells (PSCs) are favorable candidates for next-generation solar cells, due to their excellent photovoltaic performance and promising low-cost fabrication process. Particularly, tin oxide (SnO2), with excellent charge mobility and extraction efficiency, is widely used as electron transport layers (ETLs), and the efficiency of the corresponding n-i-p-type perovskites has been certified as high as 26.21% in single-junction devices. The SnO2 layer serves as the substrate for the growth of perovskite films, determining the crystalline quality and the buried interface of perovskite films. However, due to the different thermal expansion coefficient of SnO2 and perovskite, the subsequent perovskite annealing process leads to the residual stress at the buried interfaces and lattice distortion in the perovskite films, which seriously affects their optoelectronic performance and stability. To release this interfacial stress, researchers have made some progress by applying different polymers and small molecules to the SnO2/perovskite interface as a buffer layer. Among these, two-dimensional (2D) nanosheets with high carrier mobility, a wide bandgap range, and excellent optical absorption properties are promising, especially 2D NbSe2 nanosheets showing the advantages of solution-processability, high intrinsic conductivity and clean smooth surface, namely without dangling bonded atoms. Herein, 2D NbSe2 nanosheets have been introduced at the SnO2/perovskite interface to release the undesired residual tensile strain in perovskite films and to form a more matched interfacial energy level alignment. As a result, we have obtained a high-quality perovskite film and further an improved photovoltaic performance. The PCE has been increased from 21.81% to 24.05%. The unencapsulated cell maintained 91% of the initial efficiency after aging over 1000 h under atmospheric condition.

Interfacial Engineering of Au@Nb2CTx-MXene Modulates the Growth Strain, Suppresses the Auger Recombination, and Enables an Open-Circuit Voltage of over 1.2 V in Perovskite Solar Cells

24.11% High Performance Perovskite Solar Cells by Dual Interfacial Carrier Mobility Enhancement and Charge‐Carrier Transport Balance

Nb2C MXenes modified SnO2 as high quality electron transfer layer for efficient and stability perovskite solar cells

Mxene regulates the stress of perovskite and improves interface contact for high-efficiency carbon-based all-inorganic solar cells

Synergistic effect of multifunctional MXene-nanosheet and naphthoquinone sulfonate toward high-performance perovskite solar cells and modules

Buried Interface Modulation via Preferential Crystallization in All‐Inorganic Perovskite Solar Cells: The Case of Multifunctional Ti3C2Tx

MXenes as a hole transport interfacial layer for efficient and air-stable quasi-2D perovskite solar cells

Anhydrous organic etching derived fluorine-rich terminated MXene nanosheets for efficient and stable perovskite solar cells

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells

Cl-terminated Ti3C2 MXene-modulated carbon/CsPbIBr2 interface boosting efficiency and stability of all-inorganic perovskite solar cells

Laser Manufactured Nano‐MXenes with Tailored Halogen Terminations Enable Interfacial Ionic Stabilization of High Performance Perovskite Solar Cells

Electron transport bilayer with cascade energy alignment based on Nb2O5-Ti3C2 MXene/TiO2 for efficient perovskite solar cells

NbSe2 Nanosheets Improved the Buried Interface for Perovskite Solar Cells

MXene-Based Tailoring of Carrier Dynamics, Defect Passivation, and Interfacial Band Alignment for Efficient Planar p–i–n Perovskite Solar Cells

Ti3C2 MXene nanosheets modified TiO2 ETLs enables efficient solar cells with outstanding device consistency

MXene-based novel nanocomposites doped SnO2 for boosting the performance of perovskite solar cells

Interfacial Energy Level Alignment and Defect Passivation by Using a Multifunctional Molecular for Efficient and Stable Perovskite Solar Cells

Interfacial engineering using ammonia-functionalized MXene in perovskite solar cells

Heterogeneous Nucleation and Enhanced Charge Transfer via Amorphous Metal‐Organic Frameworks for Efficient and Stable Perovskite Solar Cells

Dual Interfacial Modification Engineering with 2D MXene Quantum Dots and Copper Sulphide Nanocrystals Enabled High‐Performance Perovskite Solar Cells

MXene‐Interconnected Two‐Terminal, Mechanically‐Stacked Perovskite/Silicon Tandem Solar Cell with High Efficiency