Abstract:TiB2–WC ceramic–metal composite tool materials were fabricated using Co, Ni and (Ni, Mo) as sintering additives by vacuum hot-pressing technique. The microstructure and mechanical properties of the composite were investigated. The composite was analyzed by the observations of scanning electron microscope (SEM), X-ray diffraction (XRD) and energy dispersive spectrometry (EDS). The microstructure of TiB2–WC ceramic–metal composites consisted of the fine WC grains and uniform TiB2 grains. The brittle phase of Ni3B4 and a few pores were found in TiB2–WC–Ni ceramic–metal composite. A lot of pores and brittle phases such as W2CoB2 and Co2B were formed in TiB2–WC–Co ceramic–metal composite. The liquid phase of Co was consumed by the reaction which led to the formation of the pores and the coarse grains of TiB2. The pores, brittle phases and coarse grains of TiB2 were harmful to the improvement of the mechanical properties of the composite. The sintering additive of (Ni, Mo) had a significant effect on the density and the mechanical properties of TiB2–WC ceramic–metal composite. The formation of intermetallic compound of MoNi4 inhibited the consumption of liquid phase of (Ni, Mo). The liquid phase of (Ni, Mo) not only inhibited the formation of the pores and the coarse grains of TiB2 but also strengthened the interface energy between WC and TiB2 grains. The grain size was fine and the average relative density of TiB2–WC–(Ni, Mo) ceramic–metal composite reached 99.1%. The flexural strength, fracture toughness and Vickers hardness of TiB2–WC–(Ni, Mo) ceramic–metal composite were 1307.0±121.4MPa, 8.19±0.29MPam1/2 and 22.71±0.82GPa, respectively.

Effects of Sintering Parameters and WC Addition on Properties of Iron-Nickel Pre-Alloy Matrix Diamond Composites

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Effect of Components on Mechanical Properties of Fe-matrix Bonding Diamond Tool

Effects of sintering temperature on interface microstructure and element diffusion of WC-Co-Ni-Fe/high-speed steel composites

Effect of composition of FeCoCu pre-alloyed powders on sintering characters used for diamond tools

Influence of B4C Coating on Graphitization for Diamond/wc-Fe-ni Composite

Effects of Ni on the Microstructures and Properties of WC–6Co Cemented Carbides Fabricated by WC–6(Co, Ni) Composite Powders

Low-Temperature Sintering of Fecuco Based Pre-Alloyed Powder for Diamond Bits

The Effect of Processing Parameters on the Performance of Spark Plasma Sintered Cbn-Wc-co Composites

Effect of Nickel-Plated Graphite on Microstructure and Properties of Matrix for Fe-based Diamond Tools

Effect of Nano-Vanadium Nitride on Microstructure and Properties of Sintered Fe-Cu-based Diamond Composites

Effect of WC Nanoparticles on the Microstructure and Properties of WC-Bronze-Ni-Mn Based Diamond Composites

Effect of WC Incorporation on the Microstructure and Mechanical Properties of Ni625/WC Spark Plasma Sintered Composites

Effect of Ni Addition on Microstructure of Matrix in Casting Tungsten Carbide Particle Reinforced Composite

Microstructural Evolution of Diamond-Based Composites at High Temperature and High Pressure

Effects of Nickel Powder on Microstructure and Interface of WC/steel Matrix Surface Composites

Processing of Diamond Enhanced Cemented Tungsten Carbide Insert for Rock Drilling

Effect of Tungsten Carbide Particles on Microstructure and Mechanical Properties of Cu Alloy Composite Bit Matrix

Effect of WC Content on Microstructure and Element Diffusion of Nano WC-Co-TiC/304 Stainless Steel Composites for Micro Drill

Effects of sintering additives on microstructure and mechanical properties of TiB2-WC ceramic-metal composite tool materials

Effect of sintering temperature on mechanical properties of an Al3Ni intermetallic compound reinforced Al matrix composite