Abstract:Polycrystalline diamond composites (PDC) have been used as a cutting material in a multitude of fields, from mechanical processing to oil and gas drilling. In this study, PDC samples were prepared under high pressure and high temperature (HPHT) conditions within a pressure interval of 5.5 to 10.5 GPa by sintering diamond powder (average grain size ~3 μm) with WC-10 wt% Co substrate. Samples obtained with varying sintering pressures and temperatures were characterized using Vickers hardness tester, scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results revealed that: (1) within a specified material system, each distinct sintering pressure condition corresponds to a unique optimal sintering temperature that yields the pinnacle of consolidation efficiency in samples. This optimal temperature exhibits a linearly increasing trend with rising sintering pressure; (2) at the intersection where the sintering pressure attains its optimal match with temperature, an increase in pressure fosters more intimate contact and stronger inter-grain bonding among diamond particles, thus amplifying the DD bond formation effect, which consequently leads to a linear enhancement in the Vickers hardness values of PDC with increasing sintering pressure; (3) simultaneously, under conditions of optimal temperature matching, elevating the sintering pressure notably decreases the cobalt content within the polycrystalline diamond layer of PDC samples. These findings furnish crucial experimental evidence for optimizing PDC material properties, significantly contributing to the advancement of both theoretical exploration and technological innovation within the field, carrying profound academic value and practical guidance implications.

Sub-Micron Binderless Tungsten Carbide Sintering Behavior under High Pressure and High Temperature

High-pressure Preparation of Bulk Tungsten Material with Near-Full Densification and High Fracture Toughness

Binderless nanocrystalline tungsten carbide with enhanced hardness induced by high-pressure sintering

Extraordinary High-Temperature Mechanical Properties in Binder-Free Nanopolycrystalline WC Ceramic

High-pressure Synthesis of Tungsten Carbide–cubic Boron Nitride (wc–cbn) Composites: Effect of Cbn Particle Size and Volume Fraction on Their Microstructure and Properties

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Compressibility And Strength Of Nanocrystalline Tungsten Boride Under Compression To 60gpa

Oscillatory pressure sintering of binderless tungsten carbide

Pressureless sintering of WC-TaC binderless carbide

High Pressure Synthesis of Tungsten Carbide–Cubic Boron Nitride (WC–cBN) Composites: Effect of Thermodynamic Condition and cBN Volume Fraction on their Microstructure and Properties

Change of Microstructure and Properties of WC–Co Cemented Carbides as a Result of High Pressure and Temperature

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

High temperature fracture mechanism of ultrafine WC-Co cemented carbides containing (Ti,W)C

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

The effect of binder phase content on WC-AlCoCrFeNiTi0.2 high entropy cemented carbides microstructure and mechanical properties

Rapid densification and mechanical properties of ultra-high-pressure sintered transition metal carbide ceramics

Mechanisms and mechanical properties of high-temperature high-pressure sintered vanadium carbide ceramics

Effect of pressure on sintering behavior of polycrystalline diamond