Abstract:Resonance is an important failure mechanism that arises when a periodic force acts at a frequency corresponding to a blade natural frequency. If the damping is inadequate for absorption of the periodic input energy, amplitude and stresses grow until failure occurs by overstress or by propagation of fatigue crack. A complex and irregular distribution of minor indentations covers the surface, including leading edge impacts. The damage caused by foreign objects often in the form of a geometric discontinuity like a notch. However the presence of residual stress and sub-structural damage in regions adjacent to the notch prohibit the use of simple notch analyses. FE analysis is used to estimate stress concentration effect of the geometry of the notch. For this purpose, the compressor aerofoil blade is idealized into simple rectangular cantilever plate for FEM study. The complexity of the problem is reduced to a simplex problem by assuming the aerofoil section to a flat rectangular plate. Because of the nonpresence of the aerofoil section, analysis is so simple for finding the stress concentration effect of the geometrical notch made. To analyze the stress concentration effect of foreign object damage (FOD), different notches are made by varying the notch dimensions viz., depth, radius of the notch and the location of the notch on the trailing edge of the rectangular plate. Foreign object damaged compressor blades with nicks, dents and cracks can be ground into the smooth curved cutouts to reduce the stress intensification and stress concentration with a high speed grinding wheel. In doing so, depending on the extent and type of damage, designer has a requirement to estimate size and shape of the cut-out to be made on the aerofoil that generates the known SCF. With the estimated values of SCF for different geometry of cut using FEM further a modal analysis has been conducted to assess the variation of frequencies for different geometry of cut-outs with known values of SCF to aster the correctness of the solution, the finite element analysis is carried out on a rectangular cantilever plate for which literature is available. Further the study is extended to an idealized problem of Abstract: Modal analysis has been important to the designers and operators since the inception of the Turbo machinery. Blades typically fail because of low-cycle fatigue (LCF), and high-cycle fatigue (HCF), environmental attack, Creep, Oxidation, erosion, embrittlement. In the present work the turbine blade is modeled and analyzed using finite element method the eigen value extraction for flexural and torsional modes is obtained. Foreign object damage is simulated by considering a circular crack along the leading edge of the blade. It was found that the stretching induced by the centrifugal inertia force due to the rotational motion of the blades was the cause for the increment of the bending stiffness of the structure. This resulted in maximum operational Vonmises stresses; the object is to provide understanding and information for designers to improve the life and efficiency of gas turbines.

Foreign Object Damage Diagnosis Of Aero-Engine Compressor Based On Damping Averaging Built-In Matrix Method

A Virtual Blade Tip Timing Measurement Method for Foreign Object Damage

An Improved Key-Phase-Free Blade Tip-Timing Technique for Nonstationary Test Conditions and Its Application on Large-Scale Centrifugal Compressor Blades

Damage Mode Identification of Composite Wind Turbine Blade under Accelerated Fatigue Loads Using Acoustic Emission and Machine Learning

A Hybrid Fault Diagnosis Approach for Blade Crack Detection using Blade Tip Timing

Analysis of Blade Tip Timing Data from Fan Blades with Synchronous and Non-Synchronous Vibration

Modeling And Analysis Of Flexural And Torsional Modes Of Gas Turbine Blades Considering The Foreign Object Damage

A Keyphasor-Free Traveling Waves Analysis Method Based on Blade Tip Timing and Experimental Validation

Improved Non-contact Vibration Measurement Via Acceleration-based Blade Tip Timing

Fatigue Damage Evaluation of Compressor Blade Based on Nonlinear Ultrasonic Nondestructive Testing

Correlation Analysis of Multiple Sensors for Industrial Gas Turbine Compressor Blade Health Monitoring

Fault Diagnosis of Industrial Wind Turbine Blade Bearing Using Acoustic Emission Analysis

A Novel OPR-free Method for Blade Tip Timing Based on Adaptive Variable Reference Blades

High sensitive methods for health monitoring of compressor blades and fatigue detection

Experimental Investigation on the Accuracy of Blade Tip Timing Spectral Analysis Methods

Non-Contact Measurement of Blade Vibration in an Axial Compressor

Failure Analysis of a Fighter Jet Engine Compressor Blade Due to Foreign Object Damage and High-Cycle Fatigue

Fault Diagnosis of Demountable Disk-Drum Aero-Engine Rotor Using Customized Multiwavelet Method

In Situ Detection of Turbine Blade Vibration and Prevention

Adaptive Iterative Approach for Efficient Signal Processing of Blade Tip Timing

Blade Crack Detection Using Blade Tip Timing