Abstract:A high-current vacuum arc subjected to an axial magnetic field is maintained in a diffuse status. With an increase in arc current, the energy carried by the arc column to the anode becomes larger and finally leads to the anode temperature exceeding the melting point of the anode material. When the anode melting pool is formed, and the rotational plasma of the arc column delivers its momentum to the melting pool, the anode melting pool starts to rotate and also flow outwards along the radial direction, which has been photographed by some researchers using high-speed cameras. In this paper, the anode temperature and melting status is calculated using the melting and solidification model. The swirl flow of the anode melting pool and deformation of the anode is calculated using the magneto-hydrodynamic (MHD) model with the volume of fraction (VOF) method. All the models are transient 2D axial-rotational symmetric models. The influence of the impaction force of the arc plasma, electromagnetic force, viscosity force, and surface tension of the liquid metal are all considered in the model. The heat flux density injected into the anode and the arc pressure are obtained from the 3D numerical simulation of the high-current vacuum arc using the MHD model, which gives more realistic parameters for the anode simulation. Simulation results show that the depth of the anode melting pool increases with an increase in the arc current. Some droplets sputter out from the anode surface, which is caused by the inertial centrifugal force of the rotational melting pool and strong plasma pressure. Compared with the previous anode melting model without consideration of anode deformation, when the deformation and swirl flow of the anode melting pool are considered, the anode temperature is relatively lower, and just a little more than the melting point of Cu. This is because of liquid droplets sputtering out of the anode surface taking much of the energy away from the anode surface. The azimuthal velocity of the anode melting pool for arc current 12.5 kA root-mean-square (rms) is larger than that for 17.5 kA (rms), which is likely to be caused by the thinner liquid layer, and also a smaller melting pool mass of 12.5 kA.

Aluminum Erosion Due to Fault Arcing and Its Effects on Temperature and Pressure in a Closed Air Vessel

The Effects of Metal Vapour on the Fault Arc in a Closed, Air-Filled Container

Experimental and Theoretical Investigation on Radiation Loss for a Fault Arc Between Different Material Electrodes in an Enclosed Air Tank

The influence of electrode erosion on fault arc

3-D MHD Modeling of Internal Fault Arc in a Closed Container

Experimental investigation of thermal transfer coefficient by a simplified energy balance of fault arc in a closed air vessel

Numerical Analysis Of The Influence Of Splitter-Plate Erosion On An Air Arc In The Quenching Chamber Of A Low-Voltage Circuit Breaker

The Influence of Electrode Erosion on the Air Arc in a Low-Voltage Circuit Breaker

Simulation of Surface Erosion of Anode under High-Current Vacuum Arcs

Simulation and Experimental Research on Air Are Movement Characteristics in Low-voltage Circuit Breaker Considering Electrodes Erosion

Anode Erosion Pattern Caused by Blowing Effect in Constricted Vacuum Arcs Subjected to Axial Magnetic Field

Experimental and Theoretical Study of Internal Fault Arc in A Closed Container

Modeling of the anode surface deformation in high-current vacuum arcs with AMF contacts

Electrode Evaporation Effects on Air Arc Behavior

Effect Of A Near-Cathode Sheath On Heat Transfer In High-Pressure Arc Plasmas

Effect of Contact Materials on the Transient Characteristics of Vacuum Arc Plasma and Anode Erosion

Evolution of Anodic Erosion Components and Heat Transfer Efficiency for W and W80Ag20 in Atmospheric-Pressure Arcs

High-voltage Arc Erosion Behavior and Mechanism of Ti3AlC2 under Different Ambient Atmospheres

Modeling and Simulation of Deflected Anode Erosion in Vacuum Arcs

Simulation of Fault Arc Based on Different Radiation Models in a Closed Tank

Simulation of welding arc in axial magnetic field