Abstract:For low costs, numerical simulation is an effective method to reveal the internal mechanisms inside a thermal plasma torch. Various simulation models for studying the inside or outside characteristics of thermal plasma torches have been built and discussed. However, to reveal the inside mechanisms of thermal plasma torches under various working conditions to support the materials processing, more attention should be paid to building precise models of laminar plasma torches. Thus, based on the user-defined function (UDF) and user-defined scalar (UDS) of ANSYS Fluent software, the assumptions, governing equations, boundary conditions, and solving method were discussed in detail, and a corresponding numerical model of a homemade laminar plasma torch was first built. For verifying the effectiveness of the proposed numerical model and studying the influence of the gas components on the arc characteristics, the working conditions and experimental setups were introduced in sequence. Finally, the numerical and experimental results of the homemade laminar plasma torch were obtained and discussed in detail. The study results show that: 1 The axial temperature of the plasma torch could be divided into three sections along the axis: peak temperature area (10 mm < x < 20 mm), stable temperature area (20 mm < x < 62 mm) and decrease temperature area (62 mm < x < 95 mm). Under the same input conditions, when pure argon gas was used, the peak temperature at the outlet was reached at approximately 7590 K, while for pure nitrogen and 50%Ar + 50%N2, the corresponding peak temperatures were 6785 K and 7402.2 K, respectively. 2 The axial velocity of pure nitrogen is much higher than that of pure argon and 50%Ar + 50%N2, while that of pure argon and 50%Ar + 50%N2 has little difference. In addition, when nitrogen gas was used, the peak velocity at the outlet reached 185 m/s, whereas, for argon gas and 50%Ar + 50%N2, the corresponding peak velocities were 146 m/s and 169 m/s, respectively. 3 The simulated arc voltage trends under different working conditions are well in accordance with the experimental arc voltage trends.

Thermodynamic Properties and Transport Coefficients of Air Thermal Plasmas Mixed with Ablated Vapors of Cu and Polytetrafluoroethylene

Analysis of Electromagnetic Scattering Characteristics for a HTV-2 Type Flight Vehicle Ablation Flows

Numerical Simulation of Heat Transfer and Fluid Flow of a Non-Equilibrium Argon Plasma Jet with Confined Wall

Analyses on the Nonequilibrium Transport Processes in a Free-Burning Argon Arc Plasma under Different Operating Conditions

An improved equation of state for air plasma simulations

Calculation of thermodynamic properties and transport coefficients of Ar-C-Si plasma

Experimental research on the fault arc arcing process and electrode temperature distribution of a 220VAC power system

Thermodynamic Parameters and Energy Transfer Analysis of High Enthalpy Inductively Coupled Plasma

Calculation of Two-Temperature Thermodynamic and Transport Properties of Argon-Nitrogen Plasma

Calculation of Radiative Properties for [82%Ar-18%CO2]-Fe Plasmas in MAG Welding Arc

Numerical Simulation Study on Characteristics of Gliding Arc Discharge

HEAT TRANSFER AND FLUID FLOW FOR A THERMAL PLASMA JET IMPINGING NORMALLY ON A FLAT PLATE

Numerical Study of Plasma–Electrode Interaction During Arc Discharge in a DC Plasma Torch

Modeling of the Arc Characteristics inside a Thermal Laminar Plasma Torch with Different Gas Components

High temperature properties of dry air used as arc quenching medium and its mixture with vaporized C 2 F 4 : reaction products and critical reduced electric field strength at 300-3000 K

[Research on the Electron Temperature and Emission Spectroscopy of the Atmospheric Inductively Coupled with Plasma Processing]

An experimental study on the thermal characteristics and heating effect of arc-fault from Cu core in residential electrical wiring fires

Numerical Analysis of Fluid Flow and Heat Transfer by Means of a Unified Model in a Direct Current Electric Arc Furnace

Heat Flux Characteristics In An Atmospheric Double Arc Argon Plasma Jet

Numerical Simulation of Contact Point Temperature Distribution and Fire Mechanism Analysis

Effect Of A Near-Cathode Sheath On Heat Transfer In High-Pressure Arc Plasmas