Abstract:Graphene is a promising material for many potential applications, owing to its extraordinary properties. Numerous synthesizing approaches have been developed to realize the promising applications of graphene. However, there is lack of a comprehensive way, which combines the following features, i.e. large-area growth, patterned graphene and fast growth at the same time. Here, we provide an engineering approach to both large-area and patterned graphene at a high rate. The high power and continuous-wave lasers were employed to irradiate solid carbon source coated on nickel surface. The rate of graphene production by laser irradiation exceeds 28.8 cm2/min and the solid carbon source is less hazardous compared to typical gaseous carbon sources used in chemical vapor deposition (CVD). The influence of laser process on graphene fabrication was investigated systematically. Raman analyses, optical images and scanning electron microscopy (SEM) results show that the quality of graphene strongly depends on the laser process parameters, including laser power density and scanning rate. Adjusting the parameters to input the appropriate heat, so that the high quality graphene can be obtained in an optimal condition. The influence of carbon source on graphene growth was also investigated. Ultimately, the penetration and precipitation mechanism of carbon into Ni substrate during the fabrication process were also discussed. This approach may reach the scale large enough for practical applications.Graphene is a promising material for many potential applications, owing to its extraordinary properties. Numerous synthesizing approaches have been developed to realize the promising applications of graphene. However, there is lack of a comprehensive way, which combines the following features, i.e. large-area growth, patterned graphene and fast growth at the same time. Here, we provide an engineering approach to both large-area and patterned graphene at a high rate. The high power and continuous-wave lasers were employed to irradiate solid carbon source coated on nickel surface. The rate of graphene production by laser irradiation exceeds 28.8 cm2/min and the solid carbon source is less hazardous compared to typical gaseous carbon sources used in chemical vapor deposition (CVD). The influence of laser process on graphene fabrication was investigated systematically. Raman analyses, optical images and scanning electron microscopy (SEM) results show that the quality of graphene strongly depends on the laser ...

Laser assisted deposition of good carbon—From diamond films to nanotubes

Laser-Assisted Nanofabrication of Carbon Nanostructures

A review on diamond-like carbon films grown by pulsed laser deposition

Diamond deposition on AlN using Q-carbon interlayer through overcoming the substrate limitations

Advances in laser-assisted conversion of polymeric and graphitic carbon into nanodiamond films

What Can Lasers Do in the Nano-Fabrication of Carbon Nanotube Based Devices?

Preparation of Diamond Films by Hot Filament Chemical Vapor Deposition and Nucleation by Carbon Nanotubes

Deposition of nano-diamond-like carbon films by an atmospheric pressure plasma gun and diagnostic by optical emission spectrum on the process

Synthesis and Mechanism Study of Carbon Nanowires, Carbon Nanotubes, and Carbon Pompons on Single-Crystal Diamonds

Kinetics of Laser-Assisted Carbon Nanotube Growth

Beneficial effects of laser irradiation on the deposition process of diamond/Ni60 composite coating with cold spray

Direct Laser Fabrication of Large-Area Graphene: an Engineering Approach to Nano-Materials

Laser Assisted Fabrication for Controlled Single-Walled Carbon Nanotube Synthesis and Processing（ Invited Paper）

Localized Synthesis of Carbon Nanotube Films on Suspended Microstructures by Laser-Assisted Chemical Vapor Deposition

Fabrication and application of CNT fiber-ultra-fine diamond composites via electrophoretic deposition and instantaneous Joule-heating method

Laser Direct Writing Carbon Nanotube Arrays on Transparent Substrates

Characterization of diamond thin films deposited by a CO2 laser-assisted combustion-flame method

The Development of Ultra-Fast Pulse Laser Deposition of Diamond-Like Carbon Films

Micro-structural and Optical Properties of Diamond-like Carbon Films Grown by Magnetic field-assisted Laser Deposition

DEPOSITION OF DIAMOND-LIKE AND OTHER SPECIAL COATINGS BY PULSED LASER ABLATION AND THEIR POST-SYNTHESIS PROCESSING

Laser‐Carbonization – A powerful tool for micro‐fabrication of patterned electronic carbons