Abstract:OBJECTIVETo evaluate the wear intensity and surface roughness of occlusal veneers on premolars made of microhybrid composite resin or two kinds of ceramics in vitro after the thermocycling and cyclic mechanical loading tests.METHODSIn the study,24 fresh extracted human premolars without root canal treatment were prepared (cusps reduction of 1.5 mm in thickness to simulate middle to severe tooth wear, the inclinations of cusps were 20°). The prepared teeth were restored with occlusal veneers made of three different materials: microhybrid composite, heat-pressed lithium disilicate ceramic and computer-aided design/computer-aided manufacturing (CAD/CAM) lithium disilicate ceramic in the thickness of 1.5 mm. The occlusal veneers were cemented with resin cement. The specimens were fatigued using the thermocycling and cyclic mechanical loading tests after being stored in water for 72 h. The wear of specimens was measured using gypsum replicas and 3D laser scanner before and after the thermocycling and cyclic mechanical loading tests and the mean lost distance (mm) was used to indicate the level of wear. The surfaces of occlusal contact area were observed and the surface roughness was recorded using 3D laser scanning confocal microscope before and after the fatigue test. Differences between the groups were compared using ONE-way ANOVA(P<0.05).RESULTSAll the specimens successfully survived after the thermocycling and cyclic mechanical loading tests. The mean wear of microhybrid composite group, heat-pressed lithium disilicate ceramic group, and CAD/CAM lithium disilicate ceramic group was (-0.13±0.03) mm, (-0.05±0.01) mm and (-0.05±0.01) mm, the wear of microhybrid composite was significantly higher than the two ceramic groups(P<0.001).The mean surface roughness(Ra)before the fatigue test was(1.24±0.20) μm, (0.75±0.09) μm, (0.73±0.14) μm and it became (1.81±0.24) μm, (1.53±0.26) μm and (1.77±0.23) μm after the test . Before the fatigue test, the surface roughness of microhybrid composite was significantly higher than the two ceramic groups(P<0.001) and after the test, the surface roughness of heat-pressed lithium disilicate ceramic was significantly lower than microhybrid composite(P=0.005) and CAD/CAM lithium disilicate ceramic (P=0.010).CONCLUSIONFrom the view of wear speed, microhybrid composite was significantly higher than the two kinds of ceramics, but it was similar to enamel when the opposing tooth was natural. The surface roughness before the themocycling and cyclic mechanical loading test of microhybrid composite was significantly higher than that of the two ceramic groups. After the test, the surface roughness of heat-pressed ceramic was significantly lower than that of the other two groups. From the view of surface roughness, heat-pressed ceramic has more advantage.

Marginal adaptation of different hybrid ceramic inlays after thermal cycling

Marginal adaptation study of ceramic and composite inlay

Marginal adaptation of 1 fiber-reinforced composite and 2 all-ceramic inlay fixed partial denture systems

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Influence of thermal aging on the marginal integrity of computer aided design/computer aided manufacturing fabricated crowns

Effect of thermomechanical aging on marginal fit of three CAD-CAM restorative materials: An in vitro study

Ceramic Inlay Bonded Interfaces in Minimally Invasive Preparations: Damage and Contributing Mechanisms in Sliding Contact

Marginal gap, internal fit, and fracture load of leucite-reinforced ceramic inlays fabricated by CEREC inLab and hot-pressed techniques

[Wear Intensity and Surface Roughness of Microhybrid Composite and Ceramic Occlusal Veneers on Premolars after the Thermocycling and Cyclic Mechanical Loading Tests].

The Effects of Thermocycling on the Physical Properties and Biocompatibilities of Various CAD/CAM Restorative Materials

An experimental study on marginal integrity of all-ceramic crowns cemented with different luting materials

Effect of porcelain firing and cementation on the marginal fit of implant-supported metal-ceramic restorations fabricated by additive or subtractive manufacturing methods

Comparation of marginal and internal adaption of endocrowns made from three different ceramics in vitro

Assessment of marginal adaptation and fracture resistance of endocrown restorations utilizing different machinable blocks subjected to thermomechanical aging

Evaluation on the Marginal Adaptation of CAD/CAM Ceramic Crown

Effect of Tooth Preparation Design on Marginal Adaptation of Composite Resin CAD-CAM Onlays

A Comparison of Three-Dimensional Marginal Adaptation among Three All-Ceramic Crown Systems

Marginal integrity of prototype bioactive glass-doped resin composites in class II cavities

Marginal, internal fit and microleakage of zirconia infrastructures: an in-vitro study

Marginal adaptation of crown by national CAD/CAM

Evaluation of Marginal and Internal Adaptation of Crowns Fabricated with Three Different Zirconia CAD/CAM Materials