Abstract:_ This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper IPTC 21818, “Material Selection and Corrosion-Rate Analysis for CO2 Injection Well: A Case Study of K1 Field CO2 Sequestration Project,” by Mohd A. Abu Bakar, Wan Amni Wan Mohamad, and M. Wahidullah M. Wahi, Petronas, et al. The paper has not been peer reviewed. Copyright 2021 International Petroleum Technology Conference. Reproduced by permission. _ Typical materials used for CO2 injector wells are either corrosion-resistant alloys (CRA) or epoxy-lined tubulars. The most widely adopted CRA material is 25Cr, which features a high well-application cost. Application of materials other than 25Cr for CO2 injector wells are uncommon but may be fit for purpose. The complete paper describes material-selection methodology and corrosion studies performed in the K1 field CO2 sequestration project using materials other than 25Cr in an effort to optimize well costs and improve overall project economics without jeopardizing CO2 injector-well integrity. Introduction K1 field is in the Sarawak Basin at a water depth of 453 ft. It was discovered by an exploration well in 1972 and appraised by a dedicated well in 1992. The field features a gas column of 324 ft from the free water level at 4,990 ft true vertical depth subsea. Gas initially in place for this field is estimated at approximately 2,800 Bscf. CO2 storage screening studies had identified an opportunity to use the K1 field as a storage site. The source of CO2 gas is a nearby field, from which separated CO2 gas will be transported through a 130-km pipeline to the K1 field’s new injection-wellhead platform. The current plan is to inject and store the CO2 inside one of the depleted carbonate reservoirs until an increase in reservoir pressure to the initial pressure of 3,440 psi is observed. The reservoir temperature is approximately 120°C. Injection-Fluid Composition and Presence of Water Injection fluid contains a high mol% of CO2, methane, and other impurities such as nitrogen and hydrogen sulfide (H2S) gases. Injection fluid will be injected above the CO2 supercritical condition. Based on the injection fluid’s composition, CO2 will be the main source of corrosion in the presence of water when exposed to unprotected tubulars in the wells. The presence of H2S denotes the effect of stress corrosion cracking (SCC) and sulfide stress cracking (SSC), which must be considered in selecting tubing material for the injector wells. A small percentage of water (approximately 0.0086 mol%) also exists in the injection fluid. This will be detrimental to the injection wells in terms of corrosion if it is in the aqueous phase. To study this, the well’s shut-in and injection pressures and temperatures were plotted against the water-phase diagram. During these conditions, water in the injection fluid exists as vapor phase. Considering the possible risks of a higher percentage of water in the injection fluid, a more- conservative approach was taken in the selection of tubing material for the injector wells.

An Analytical Model for the Corrosion Risk of Water Alternating Gas Injection Wells in CO2 Enhanced Oil Recovery

One-dimensional Analytical Model for Thermo-Hydro-mechanical Coupling Behaviour of Hydrates Overlying Layer During Gas Production

Corrosion Control in CO2 Enhanced Oil Recovery from a Perspective of Multiphase Fluids

CFD-Based Erosion and Corrosion Modeling of a Pipeline with CO2-Containing Gas–Water Two-Phase Flow

Research on Wellbore Integrity Evaluation Model of CO2 Enhanced Composite Fracturing

Risk Assessment of Annular Pressure Caused by Tubing Leakage in Offshore Gas Wells with High CO2

Double Circular Arc Model Based on Average Shear Stress Yield Criterion and Its Application in the Corroded Pipe Burst

Corrosion Inhibitor Distribution and Injection Cycle Prediction in a High Water-Cut Oil Well: A Numerical Simulation Study

Analysis of depleted gas reservoir underground gas storage wellbore integrity change during gas injection and production processes

Study on Failure Behavior of Gas Well Tubing Under CO 2 Corrosion After Erosion

A Mechanistic Model for Pipeline Steel Corrosion in Supercritical CO2–SO2–O2–H2O Environments

Risk assessment of corroded casing based on analytic hierarchy process and fuzzy comprehensive evaluation

Analysis of corrosion failure and materials selection for CO2–H2S gas well

Effect of CO2 content on corrosion non-uniformity of 20# steel in oil–water two-phase based on wire beam electrode technique

Anti-corrosion study of tungsten alloy coating on tube column under high CO2 partial pressure

Numerical Simulation of Corrosive Flow in the Production End of CCUS-EOR Backflow Wastewater Pipeline

Developing a Water Chemistry Model in the CO2-mixed Salts-H2o System to Predict the Corrosion of Carbon Steel in Supercritical CO2-containing Formation Water

Main control factors and prediction model of flow-accelerated CO2/H2S synergistic corrosion for X65 steel

Offshore Oilfield Gas Injection Wells Erosion Study and Evaluation

Material Selection and Corrosion Rate Analyzed for CO2 Injection Well

Prediction models of burst strength degradation for casing with considerations of both wear and corrosion