Abstract:Photoelectrochemical water splitting (PEC) is a viable solution for addressing future environmental and energy concerns. However, due to the high cost of photoelectrodes and the limitations of sluggish kinetics, practical applications are limited. To achieve that goal, effective solutions are still needed to create low-cost photoelectrodes suited for PEC. Transistion metal sulfides (TMS) materials have a high potential for use as photoelectrodes due to their favorable and impressive properties 1 . The photoactivity of TMS is typically unlimited due to low reflection at the grain boundary. The individual atomic thin sheets with higher surface area compared to bulk materials allow for faster diffusion of photoinduced charge carriers primarily due to the less interface between their grains. Their lower interfacial contact resistance enables enhanced charge dynamics and, as a result, improved electrochemical reaction kinetics. When compared to other TMS, CdS has a direct bandgap and excellent photoactivity. However, its toxicity and photocorrosion make it unsuitable for long-term practical use. WS 2 is well-known layered transition metal sulfide that has a 2D molybdenite structure. It is non-toxic in acidic/neutral solutions that are chemically stable. It has been demonstrated to be more stable against oxidation and photo corrosion than CdS, which is extensively employed in photocatalysis 2 . However, because of the recombination of photoinduced charge carriers, pure WS 2 exhibits relatively poor photocatalytic efficiency and stability. As a result, combining WS 2 based photoactive nanomaterials with other suitable materials has helped overcome this challenge. Transistion metal sulfides with acceptable band structures for heterostructure construction with WS 2 may enable breakthroughs in photocatalytic and photo-electrochemical processes. The primary focus of this work is to construct heterostructures by combining CdS and WS 2 and to investigate their role as photoanodes of semiconductor materials in PEC water splitting. In this work, we have synthesised heterostructures using a facile solution-reaction method and Successive Ionic Layer Adsorption Reaction deposition (SILAR) technique which is intrinsically cost effective and scalable 3 . The heterostructure is characterised by XRD, SEM and TEM. We also studied the performance enhancement of this heterostructure using Linear sweep voltammetry and Electrochemical impedance spectroscopy. Pristine WS 2 and CdS showed photocurrent densities of 3 μA cm -2 and 20 μA cm -2 . However, heterostructures formation led to much improved photocurrents. Photocurrent densities of 151 μA cm -2 were observed for WS 2 /CdS heterostructures respectively at 1.23 V vs RHE. The enhanced improvement in photoelectrochemical performance in the case of the heterostructures could be due to the following factors: (a) the intimate interaction of this unique heterostructure improves adhesion and lowers the photoinduced charge transfer barrier; (b) increased light harvesting capability; and (c) improved charge dynamics of photoinduced charge carriers due to proper band alignment. The current study paves the way for further research into the creation of metal sulfide heterostructures that generate analogous photoelectrode materials. Keywords: Photoelectrochemical water splitting, metal sulfides, photoelectrodes. Figure 1

Photo/Electrochemical Applications of Metal Sulfide/TiO2 Heterostructures

Enhanced hydrogen evolution via interlaced Ni 3 S 2 /MoS 2 heterojunction photocatalysts with efficient interfacial contact and broadband absorption

Enhanced Photoelectrochemical Performance in Engineered Interface 2D Metal Sulfide Heterostructures for Water Splitting

Facile Construction TiO2/ZnIn2S4/Zn0.4Ca0.6In2S4 Ternary Hetero-Structure Photo-Anode with Enhanced Photo-Electrochemical Water-Splitting Performance

Constructing metal sulfide-based S-scheme heterojunctions for efficient photocatalytic reaction: a mini review of recent advances

Photocatalytic Hydrogen Evolution Using Ternary‐Metal‐Sulfide/TiO 2 Heterojunction Photocatalysts

Metal-sulfide-based heterojunction photocatalysts: Principles, impact, applications, and in-situ characterization

TiO2-based photocatalysts from type-II to S-scheme heterojunction and their applications

Recent Advances in Nanoscale Engineering of Ternary Metal Sulfide-Based Heterostructures for Photocatalytic Water Splitting Applications

Mixed Metal Sulfides for the Application of Photocatalytic Energy Conversion

When Mos2 Meets Tio2: Facile Synthesis Strategies, Hybrid Nanostructures, Synergistic Properties, And Photocatalytic Applications

1T-Mo1-xwxs2/cds Heterostructure Enabling Robust Photocatalytic Water Splitting: Unveiling the Interfacial Charge Polarization

TiO2-Based Catalysts with Various Structures for Photocatalytic Application: A Review

TiO2-based S-scheme photocatalysts for solar energy conversion and environmental remediation

Fabrication of Z-Scheme TiO2/SnS2/MoS2 ternary heterojunction arrays for enhanced photocatalytic and photoelectrochemical performance under visible light

Heterojunction Engineering of Multinary Metal Sulfide‐Based Photocatalysts for Efficient Photocatalytic Hydrogen Evolution

S-scheme heterojunction/Schottky junction tandem synergistic effect promotes visible-light-driven catalytic activity

TiO 2 NTs/MoS 2 -CdS Hybrid Photocathode for Visible Light-driven Photoelectrochemical Performance: Waste Water Remediation, Photoelectric Conversion and Hydrogen Generation

Fabrication of Flower-Shaped Sb2S3/Fe2O3 Heterostructures for Enhanced Photoelectrochemical Performance

Fine tuning of charge motion over homogeneous transient metal chalcogenides heterostructured photoanodes for photoelectrochemical water splitting

A Hierarchical Heterostructure of CdS QDs Confined on 3D ZnIn2S4 with Boosted Charge Transfer for Photocatalytic CO2 Reduction