Abstract:Photoelectrochemical water splitting (PEC) is a viable solution for addressing future environmental and energy concerns. However, due to the high cost of photoelectrodes and the limitations of sluggish kinetics, practical applications are limited. To achieve that goal, effective solutions are still needed to create low-cost photoelectrodes suited for PEC. Transistion metal sulfides (TMS) materials have a high potential for use as photoelectrodes due to their favorable and impressive properties 1 . The photoactivity of TMS is typically unlimited due to low reflection at the grain boundary. The individual atomic thin sheets with higher surface area compared to bulk materials allow for faster diffusion of photoinduced charge carriers primarily due to the less interface between their grains. Their lower interfacial contact resistance enables enhanced charge dynamics and, as a result, improved electrochemical reaction kinetics. When compared to other TMS, CdS has a direct bandgap and excellent photoactivity. However, its toxicity and photocorrosion make it unsuitable for long-term practical use. WS 2 is well-known layered transition metal sulfide that has a 2D molybdenite structure. It is non-toxic in acidic/neutral solutions that are chemically stable. It has been demonstrated to be more stable against oxidation and photo corrosion than CdS, which is extensively employed in photocatalysis 2 . However, because of the recombination of photoinduced charge carriers, pure WS 2 exhibits relatively poor photocatalytic efficiency and stability. As a result, combining WS 2 based photoactive nanomaterials with other suitable materials has helped overcome this challenge. Transistion metal sulfides with acceptable band structures for heterostructure construction with WS 2 may enable breakthroughs in photocatalytic and photo-electrochemical processes. The primary focus of this work is to construct heterostructures by combining CdS and WS 2 and to investigate their role as photoanodes of semiconductor materials in PEC water splitting. In this work, we have synthesised heterostructures using a facile solution-reaction method and Successive Ionic Layer Adsorption Reaction deposition (SILAR) technique which is intrinsically cost effective and scalable 3 . The heterostructure is characterised by XRD, SEM and TEM. We also studied the performance enhancement of this heterostructure using Linear sweep voltammetry and Electrochemical impedance spectroscopy. Pristine WS 2 and CdS showed photocurrent densities of 3 μA cm -2 and 20 μA cm -2 . However, heterostructures formation led to much improved photocurrents. Photocurrent densities of 151 μA cm -2 were observed for WS 2 /CdS heterostructures respectively at 1.23 V vs RHE. The enhanced improvement in photoelectrochemical performance in the case of the heterostructures could be due to the following factors: (a) the intimate interaction of this unique heterostructure improves adhesion and lowers the photoinduced charge transfer barrier; (b) increased light harvesting capability; and (c) improved charge dynamics of photoinduced charge carriers due to proper band alignment. The current study paves the way for further research into the creation of metal sulfide heterostructures that generate analogous photoelectrode materials. Keywords: Photoelectrochemical water splitting, metal sulfides, photoelectrodes. Figure 1

Fine tuning of charge motion over homogeneous transient metal chalcogenides heterostructured photoanodes for photoelectrochemical water splitting

Facile Construction TiO2/ZnIn2S4/Zn0.4Ca0.6In2S4 Ternary Hetero-Structure Photo-Anode with Enhanced Photo-Electrochemical Water-Splitting Performance

Modulating Interfacial Charge Transfer Behavior through the Construction of a Hetero-Interface for Efficient Photoelectrochemical Water Splitting

Synthesis of a Cu 2 O/Carbon Film/NiCoB‐Grpahene Oxide Heterostructure As Photocathode for Photoelectrochemical Water Splitting

Integrating Zeolite-Type Chalcogenide with Titanium Dioxide Nanowires for Enhanced Photoelectrochemical Activity.

Efficient photoelectrodes based on two-dimensional transition metal dichalcogenides heterostructures: from design to construction

Precise interface modulation cascade enables unidirectional charge transport

Customizing Dumbbell-shaped Heterostructured Artificial Photosystems Steering Versatile Photoredox Catalysis

Engineering the Interface of Cu/MoS 2 Nanostructures for Improved Charge Transfer for Applications as PEC Anode Materials

Highly efficient 3D/0D CdIn2S4/Cu2O photoanode with p-n type heterojunction for boosted photoelectrochemical water splitting under visible light irradiation

General In Situ Photoactivation Route with IPCE over 80% toward CdS Photoanodes for Photoelectrochemical Applications

Optimized the Carrier Transport Path and Separation Efficiency of 2D/2D Heterojunction in Photoelectrochemical Water Splitting

Enhanced photoelectrochemical water splitting efficiency of CdS through Fe-S-Cd carrier channel facilitated interfacial charge transfer

Enhanced Photoelectrochemical Performance in Engineered Interface 2D Metal Sulfide Heterostructures for Water Splitting

Two‐Dimentional Nanostructured Metal Oxide/Sulfide–Based Photoanode for Photoelectrochemical Water Splitting

1T-Mo1-xwxs2/cds Heterostructure Enabling Robust Photocatalytic Water Splitting: Unveiling the Interfacial Charge Polarization

Efficient photoanode with a MoS2/TiO2/Au nanoparticle heterostructure for ultraviolet-visible photoelectrocatalysis

Realizing Efficient Photoelectrochemical Performance for Well-Designed CdS@ZnIn2S4 Heterostructure Photoanode with Directional Interfacial Charge Transfer Dynamics

Stable Unbiased Photo‐Electrochemical Overall Water Splitting Exceeding 3% Efficiency via Covalent Triazine Framework/Metal Oxide Hybrid Photoelectrodes

Design and In Situ Growth of Cu 2 O‐Blended Heterojunction Directed by Energy‐Band Engineering: Toward High Photoelectrochemical Performance

Improving Charge Transfer Beyond Conventional Heterojunction Photoelectrodes: Fundamentals, Strategies and Applications