Abstract:Photoelectrochemical water splitting (PEC) is a viable solution for addressing future environmental and energy concerns. However, due to the high cost of photoelectrodes and the limitations of sluggish kinetics, practical applications are limited. To achieve that goal, effective solutions are still needed to create low-cost photoelectrodes suited for PEC. Transistion metal sulfides (TMS) materials have a high potential for use as photoelectrodes due to their favorable and impressive properties 1 . The photoactivity of TMS is typically unlimited due to low reflection at the grain boundary. The individual atomic thin sheets with higher surface area compared to bulk materials allow for faster diffusion of photoinduced charge carriers primarily due to the less interface between their grains. Their lower interfacial contact resistance enables enhanced charge dynamics and, as a result, improved electrochemical reaction kinetics. When compared to other TMS, CdS has a direct bandgap and excellent photoactivity. However, its toxicity and photocorrosion make it unsuitable for long-term practical use. WS 2 is well-known layered transition metal sulfide that has a 2D molybdenite structure. It is non-toxic in acidic/neutral solutions that are chemically stable. It has been demonstrated to be more stable against oxidation and photo corrosion than CdS, which is extensively employed in photocatalysis 2 . However, because of the recombination of photoinduced charge carriers, pure WS 2 exhibits relatively poor photocatalytic efficiency and stability. As a result, combining WS 2 based photoactive nanomaterials with other suitable materials has helped overcome this challenge. Transistion metal sulfides with acceptable band structures for heterostructure construction with WS 2 may enable breakthroughs in photocatalytic and photo-electrochemical processes. The primary focus of this work is to construct heterostructures by combining CdS and WS 2 and to investigate their role as photoanodes of semiconductor materials in PEC water splitting. In this work, we have synthesised heterostructures using a facile solution-reaction method and Successive Ionic Layer Adsorption Reaction deposition (SILAR) technique which is intrinsically cost effective and scalable 3 . The heterostructure is characterised by XRD, SEM and TEM. We also studied the performance enhancement of this heterostructure using Linear sweep voltammetry and Electrochemical impedance spectroscopy. Pristine WS 2 and CdS showed photocurrent densities of 3 μA cm -2 and 20 μA cm -2 . However, heterostructures formation led to much improved photocurrents. Photocurrent densities of 151 μA cm -2 were observed for WS 2 /CdS heterostructures respectively at 1.23 V vs RHE. The enhanced improvement in photoelectrochemical performance in the case of the heterostructures could be due to the following factors: (a) the intimate interaction of this unique heterostructure improves adhesion and lowers the photoinduced charge transfer barrier; (b) increased light harvesting capability; and (c) improved charge dynamics of photoinduced charge carriers due to proper band alignment. The current study paves the way for further research into the creation of metal sulfide heterostructures that generate analogous photoelectrode materials. Keywords: Photoelectrochemical water splitting, metal sulfides, photoelectrodes. Figure 1

Fabrication of Flower-Shaped Sb2S3/Fe2O3 Heterostructures for Enhanced Photoelectrochemical Performance

Enhanced hydrogen evolution via interlaced Ni 3 S 2 /MoS 2 heterojunction photocatalysts with efficient interfacial contact and broadband absorption

Direct Z Scheme- Fashioned Photoanode Systems Consisting of Fe2O3 Nanorod Arrays and Underlying Thin Sb2Se3 Layers Toward Enhanced Photoelectrochemical Water Splitting Performance

Facile Construction TiO2/ZnIn2S4/Zn0.4Ca0.6In2S4 Ternary Hetero-Structure Photo-Anode with Enhanced Photo-Electrochemical Water-Splitting Performance

Fabrication of In2O3/In2S3 heterostructures for enhanced photoelectrochemical performance

Combined heterostructures between Bi2S3 nanosheets and H2-treated TiO2 nanorods for enhanced photoelectrochemical water splitting

In-situ construction of novel Sb2(S,Se)3/CdSe S-scheme heterojunction with enhanced photoelectrochemical performance

Transparent, High‐Performance and Stable Sb2S3 Photoanode Enabled by Heterojunction Engineering with Conjugated Polycarbazole Frameworks for Unbiased Photoelectrochemical Overall Water Splitting Devices

Criss-crossed α-Fe2O3 nanorods/Bi2S3 heterojunction for enhanced photoelectrochemical water splitting

In-Sb Covalent Bonds over Sb2Se3/In2Se3 Heterojunction for Enhanced Photoelectrochemical Water Splitting

Construction of direct Z-scheme SnS@In2S3 core-shell heterojunction and its photoelectrochemical properties

Complementary photoelectrochemical performances between dual heterojunctions and homojunction to achieve efficient solar water splitting of ZnIn 2 S 4 -based photoanode

Covalent SO Bonding Enables Enhanced Photoelectrochemical Performance of Cu 2 S/Fe 2 O 3 Heterojunction for Water Splitting

Fast charge transfer kinetics in Sv-ZnIn2S4/Sb2S3 S-scheme heterojunction photocatalyst for enhanced photocatalytic hydrogen evolution

FeOOH decorated Sb2Se3@Cd Zn1-S core-shell nanorod heterostructure photocathode for enhancing photoelectrochemical performance

Enhanced Photoelectrochemical Performance in Engineered Interface 2D Metal Sulfide Heterostructures for Water Splitting

Construction of core–shell FeS2@ZnIn2S4 hollow hierarchical structure S-scheme heterojunction for boosted photothermal-assisted photocatalytic H2 production

Enhanced photoelectrochemical water splitting efficiency of CdS through Fe-S-Cd carrier channel facilitated interfacial charge transfer

Sb2S3/Sb2Se3 heterojunction for high-performance photodetection and hydrogen production

Low-cost processed antimony sulfide nanocrystal photoanodes with increased efficiency and stability

MoSSe/Hf(Zr)S2heterostructures used for efficient Z-scheme photocatalytic water-splitting