Abstract:This research explores the behavior of Co40Fe40W10B10 when it is sputtered onto Si(100) substrates with a thickness (tf) ranging from 10 nm to 100 nm, and then altered by an annealing process at temperatures of 200 °C, 250 °C, 300 °C, and 350 °C, respectively. The crystal structure and grain size of Co40Fe40W10B10 films with different thicknesses and annealing temperatures are observed and estimated by an X-ray diffractometer pattern (XRD) and full-width at half maximum (FWHM). The XRD of annealing Co40Fe40W10B10 films at 200 °C exhibited an amorphous status due to insufficient heating drive force. Moreover, the thicknesses and annealing temperatures of body-centered cubic (BCC) CoFe (110) peaks were detected when annealing at 250 °C with thicknesses ranging from 80 nm to 100 nm, annealing at 300 °C with thicknesses ranging from 50 nm to 100 nm, and annealing at 350 °C with thicknesses ranging from 10 nm to 100 nm. The FWHM of CoFe (110) decreased and the grain size increased when the thickness and annealing temperature increased. The CoFe (110) peak revealed magnetocrystalline anisotropy, which was related to strong low-frequency alternative-current magnetic susceptibility (χac) and induced an increasing trend in saturation magnetization (Ms) as the thickness and annealing temperature increased. The contact angles of all Co40Fe40W10B10 films were less than 90°, indicating the hydrophilic nature of Co40Fe40W10B10 films. Furthermore, the surface energy of Co40Fe40W10B10 presented an increased trend as the thickness and annealing temperature increased. According to the results, the optimal conditions are a thickness of 100 nm and an annealing temperature of 350 °C, owing to high χac, large Ms, and strong adhesion; this indicates that annealing Co40Fe40W10B10 at 350 °C and with a thickness of 100 nm exhibits good thermal stability and can become a free or pinned layer in a magnetic tunneling junction (MTJ) application.

ANISOTROPY BEHAVIOR OF SURFACE MORPHOLOGY AND PHASE STRUCTURE OF Cu-W THIN FILMS

Fractal Description of Surface Topography of Ultrathin Au Films

Influence of Post-Annealing Treatment on the Morphology of Au Films Deposited on Liquid Surfaces

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Annealing Effect on the Contact Angle, Surface Energy, Electric Property, and Nanomechanical Characteristics of Co40Fe40W20 Thin Films

Effects of Periods on the Evolution of Microstructure and Mechanical Properties of Multilayered Cu-W Films During Thermal Annealing

Continuum Modeling of Surface Roughening in Heteroepitaxial Structures Based on Phase Field Theory

Insights into Fractal Feature Evolution from Au/Ge Thin Films after Annealing

Investigation on the Interfacial Stability of Multilayered Cu–W Films at Elevated Deposition Temperatures During Co-Sputtering

Multifractal analysis of the spatial distribution of the film surfaces with different roughening mechanisms

Heterogeneous Morphologies and Hardness of Co-Sputtered Thin Films of Concentrated Cu-Mo-W Alloys

Effect of Annealing Temperature on the Formation of Silicides and the Surface Morphologies of PtSi Films

Three-dimensional Phase Field Simulation for Surface Roughening of Heteroepitaxial Films with Elastic Anisotropy

Surface alloying and pinhole formation in ultra-thin Fe/Cu(100) films

Analysing the surface morphology of annealed FTO/ZnS bilayer films: stereometric, fractal, and wettability approaches

In-situ observation of transition between surface relief and wrinkling in thin film shape memory alloys.

Annealing Effect on the Characteristics of Co40Fe40W10B10 Thin Films on Si(100) Substrate

NETWORK FRACTAL AND ANNEALING-INDUCED AGGREGATION OF Cu/a-C:H BILAYER FILMS

Influence of thermal annealing on the microstructure evolution, fracture and fatigue behavior of nanocrystalline Cu films

Surface Roughness Analysis of Cu Films Deposited on Si Substrates: A Molecular Dynamic Analysis

How metal films de-wet substrates - identifying the kinetic pathways and energetic driving forces